Nissan Cube. Manual — part 85
FRONT DISC BRAKE
BR-33
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT DISC BRAKE
BRAKE PAD
BRAKE PAD : Exploded View
INFOID:0000000009949232
BRAKE PAD : Removal and Installation
INFOID:0000000009949233
REMOVAL
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• Never spill or splash brake fluid on the disc rotor.
1.
Remove tires with power tool.
2.
Remove lower sliding pin bolt.
3.
Suspend the cylinder body with suitable wire so that the brake hose will not stretch. Then remove the
brake pads, shims, shim covers and pad retainers from the torque member.
CAUTION:
• Never deform the pad retainer when removing the pad retainer from the torque member.
• Never damage the piston boot.
• Never drop the brake pads, shims, and the shim covers.
• Remember each position of the removed brake pads.
INSTALLATION
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• Never spill or splash brake fluid on the disc rotor.
1.
Cylinder body
2.
Inner shim cover
3.
Inner shim
4.
Inner pad (with pad wear sensor)
5.
Pad retainer
6.
Torque member
7.
Outer pad (with pad wear sensor)
8.
Outer shim
9.
Outer shim cover
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
Refer to
for symbols not described on the above.
JPFIA0547GB
BR-34
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
1.
Install the pad retainers to the torque member if the pad retainers has been removed.
CAUTION:
• Securely assemble the pad retainers so that it will not be lifted up from the torque member.
• Never deform the pad retainers.
2.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the mating faces between the inner
shim and the inner pad, and install them to the inner pad.
CAUTION:
Always replace the shim together with the shim cover when replacing the brake pad.
3.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the mating faces between the outer
shim and the outer shim cover, and install them to the outer pad.
CAUTION:
Always replace the shim together with the shim cover when replacing the brake pad.
4.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the mating faces between the brake
pads and the pad retainers, and Install the brake pads to the torque member.
5.
Install cylinder body to torque member.
CAUTION:
• Never damage the piston boot.
• When replacing brake pad with new one, check a brake fluid level in the reservoir tank because
brake fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
6.
Install the lower sliding pin bolt and tighten it to the specified torque.
7.
Depress the brake pedal several times to check that no drag feel is present for the front disc brake. Refer
to
BR-34, "BRAKE PAD : Inspection"
.
8.
Install tires.
BRAKE PAD : Inspection
INFOID:0000000009949234
INSPECTION AFTER REMOVAL
Replace the shims and the shim covers if rust is excessively attached.
INSPECTION AFTER INSTALLATION
1.
Check a drag of front disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads. Refer to
BR-33, "BRAKE PAD : Exploded View"
3.
Press the pistons. Refer to
BR-33, "BRAKE PAD : Removal and Installation"
.
4.
Install brake pads. Refer to
BR-33, "BRAKE PAD : Exploded View"
.
5.
Depress the brake pedal several times.
6.
Check a drag of front disc brake again. If any drag is found, disassemble the cylinder body. Refer to
36, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
7.
Burnish contact surfaces brake pads and disc rotor after refinishing or replacing brake pads, or if a soft
pedal occurs at very low mileage. Refer to
BR-14, "BRAKE PAD : Inspection and Adjustment"
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000009949235
REMOVAL
FRONT DISC BRAKE
BR-35
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
DISASSEMBLY
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000009949236
REMOVAL
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
1.
Brake caliper assembly
Refer to
JPFIA0510GB
1.
Cap
2.
Bleeder valve
3.
Cylinder body
4.
Piston seal
5.
Piston
6.
Piston boot
7.
Sliding pin
8.
Sliding pin boot
9.
Bushing
10.
Torque member
: Apply rubber grease.
: Apply brake fluid.
Refer to
for symbols not described on the above.
JPFIA0511GB
BR-36
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface.
1.
Remove tires with power tool.
2.
Fix the disc rotor using wheel nuts.
3.
Drain brake fluid. Refer to
.
CAUTION:
Never spill or splash brake fluid on the disc rotor.
4.
Remove union bolt and copper washer, and disconnect brake hose from caliper assembly. Refer to
.
CAUTION:
Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
5.
Remove torque member mounting bolts, and remove brake caliper assembly.
CAUTION:
Never drop brake pad and caliper assembly.
6.
Remove disc rotor.
CAUTION:
• Put matching marks on the wheel hub and bearing assembly and the disc rotor before removing
the disc rotor.
• Never drop disc rotor.
INSTALLATION
WARNING:
Since dust covering the front brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface.
• Never allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
1.
Install disc rotor.
CAUTION:
Align the matching marks that have been made during removal when reusing the disc rotor.
2.
Install the brake caliper assembly to the steering knuckle and tighten the torque member mounting bolts to
the specified torque.
CAUTION:
Never spill or splash any grease and moisture on the brake caliper assembly mounting face,
threads, mounting bolts and washers. Wipe out any grease and moisture.
3.
Install brake hose and copper washers to brake caliper assembly, and tighten union bolts to the specified
torque. Refer to
BR-20, "FRONT : Exploded View"
CAUTION:
Never reuse copper washer.
4.
Refill with new brake fluid and perform the air bleeding. Refer to
BR-11, "Bleeding Brake System"
.
CAUTION:
• Never reuse drained brake fluid.
• Never spill or splash brake fluid on the disc rotor.
5.
Check a drag of front disc brake. If any drag is found, refer to
BR-38, "BRAKE CALIPER ASSEMBLY :
.
6.
Install tires.
BRAKE CALIPER ASSEMBLY : Disassembly and Assembly
INFOID:0000000009949237
DISASSEMBLY
NOTE:
Never remove the torque member, brake pad and pad retainers when disassembling and assembling the cyl-
inder body.
1.
Remove the sliding pin bolt, and remove the cylinder body from the torque member. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст