Nissan Cube. Manual — part 276
DLK-370
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
• Check door lock cable is properly engaged with outside handle bracket.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000009950826
INSIDE HANDLE : Removal and Installation
INFOID:0000000009950827
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Remove inside handle mounting bolts, slide handle toward rear of vehicle, disengage handle from door
panel, and remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
: Pawl
: Vehicle front
JMKIA3961GB
REAR DOOR LOCK
DLK-371
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded View
INFOID:0000000009950828
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009950829
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Fully close rear door glass.
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
: Pawl
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3961GB
JMKIA1467ZZ
DLK-372
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA0560ZZ
JMKIA0524ZZ
BACK DOOR LOCK
DLK-373
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000009950830
DOOR LOCK : Removal and Installation
INFOID:0000000009950831
REMOVAL
1.
Remove back door finisher lower. Refer to
INT-27, "Removal and Installation"
.
2.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Remove back door outside handle. Refer to
DLK-374, "OUTSIDE HANDLE : Removal and Installation"
.
4.
Remove back door lock assembly mounting bolts.
5.
Disconnect harness connector from back door lock assembly.
6.
Remove back door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
OUTSIDE HANDLE
JMKIA3962GB
1.
TORX bolt
2.
Outside handle bracket
3.
Rear gasket
4.
Outside handle
5.
Outside handle escutcheon
6.
Front gasket
7.
Back door lock assembly
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст