Nissan Cube. Manual — part 193
DLK-38
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in
the P position (CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000009950460
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”
*
)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK”
*
to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”
*
.) to low power consumption mode
LOCK
Power supply position is “LOCK”
*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DIAGNOSIS SYSTEM (BCM)
DLK-39
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WORK SUPPORT
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function
DATA MONITOR
The BCM input/output signals are displayed
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM
Monitor item
Description
DOOR LOCK-UNLOCK SET
Selective unlock function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: This item is displayed, but cannot be monitored
• MODE 6: This item is displayed, but cannot be monitored
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode.
• Off: non-operational
• Unlock Only: door unlock operation only
• Lock Only: door lock operation only
• Lock/Unlock: lock/unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
DLK-40
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000009950461
WORK SUPPORT
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT screen is
touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is touched
Monitor item
Description
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode
• MODE 1: 0.5 sec
• MODE 2: Non-operation
• MODE 3: 1.5 sec
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be monitored
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
HAZARD ANSWER BACK
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock/unlock operation
• Off: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch (driver side and pas-
senger side) can be selected from the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation
DIAGNOSIS SYSTEM (BCM)
DLK-41
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) with this mode
• On: Operate
• Off: Non-operation
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of brake switch power supply
BRAKE SW 2
Indicates [On/Off] condition of brake switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
S/L -LOCK
NOTE:
This item is displayed, but cannot be monitored
S/L -UNLOCK
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY -F/B
NOTE:
This item is displayed, but cannot be monitored
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст