Nissan Cube. Manual — part 521
GI-52
< BASIC INSPECTION >
CONSULT/GST CHECKING SYSTEM
JRAWC0878GB
INSPECTION AND ADJUSTMENT
GI-53
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Re-
quired Procedure After Battery Disconnection
INFOID:0000000009947066
*: Not equipped.
SYSTEM
ITEM
REFERENCE
Automatic air conditioning sys-
tem
Temperature setting trimmer
HAC-10, "Temperature Setting Trimmer"
Foot position setting trimmer*
—
Inlet port memory function
HAC-11, "Inlet Port Memory Function"
Inlet port memory function (FRE)*
—
Inlet port memory function (REC)*
—
Gas sensor sensitivity adjustment function*
—
Auto intake switch interlocking movement change*
—
Clean switch interlocking movement change*
—
Automatic drive positioner*
Automatic drive positioner system
—
Power window control
Power window control system
PWC-5, "ADDITIONAL SERVICE WHEN RE-
MOVING BATTERY NEGATIVE TERMINAL :
Sunroof system
Sunroof system
—
Sunshade system
Sunshade system
—
Rear view monitor
Rear view monitor predictive course line center po-
sition adjustment
—
Around view monitor*
Predictive course line center position adjustment
—
Automatic back door system*
Automatic back door system
—
Engine oil level read*
Engine oil level read
—
GW-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
GW
A
B
GW
N
O
P
CONTENTS
GLASS & WINDOW SYSTEM
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing of Battery Terminal . .....
Precaution for Procedure without Cowl Top Cover
. ..
Handling for Adhesive and Primer . . . . . . ....
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
WINDSHIELD GLASS . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SIDE WINDOW GLASS . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
BACK DOOR WINDOW GLASS . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT DOOR GLASS . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ..
FRONT REGULATOR . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ..
REAR DOOR GLASS . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ..
REAR REGULATOR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
GW-2
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SYMPTOM DIAGNOSIS
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000009949291
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer comments. Refer to
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that the customer is
concerned about. This can be accomplished by performing a test drive with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so that the customer, service adviser, and technician use the same language when describing
the noise.
• Squeak – (Like tennis shoes on a clean floor)
Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard sur-
faces = high-pitched noise / softer surfaces = low-pitched noises / edge to surface = chirping
• Creak – (Like walking on an old wooden floor)
Creak characteristics include firm contact / slow movement/twisting with a rotational movement / pitch
dependent on materials / often brought on by activity.
• Rattle – (Like shaking a baby rattle)
Rattle characteristics include fast repeated contact / vibration or similar movement / loose parts/missing clip
or fastener / incorrect clearance.
• Knock – (Like a knock on a door)
Knock characteristics include hollow sounds / sometimes repeating / often brought on by driver action.
• Tick – (Like a clock second hand)
Tick characteristics include gentle contacting of light materials / loose components / can be caused by driver
action or road conditions.
• Thump – (Heavy, muffled knock noise)
Thump characteristics include softer knock / dull sounds often brought on by activity.
• Buzz – (Like a bumblebee)
Buzz characteristics include high frequency rattle / firm contact.
• Often the degree of acceptable noise level varies depending upon the person. A noise that a technician may
judge as acceptable may be very irritating to a customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
SBT842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст