Nissan Cube. Manual — part 501
FUEL TANK
FL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
3.
After connecting, pull out quick connector and centralized under
floor piping by hand. Check connections are secure.
Inspection
INFOID:0000000009950430
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
A
: Pull
JPBIA0140ZZ
FL-14
< REMOVAL AND INSTALLATION >
EVAP CANISTER
EVAP CANISTER
Exploded View
INFOID:0000000009950431
Removal and Installation
INFOID:0000000009950432
REMOVAL
1.
Lift up the vehicle.
2.
Remove EVAP canister fixing bolt.
3.
Remove EVAP canister.
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
Inspection
INFOID:0000000009950433
Check EVAP canister as per the following:
1.
Block port (B).
2.
Blow air into port (A) and check that it flows freely out of port (C).
3.
Release blocked port (B).
4.
Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5.
Block port (A) and (B).
6.
Apply pressure to port (C) and check that there is no leakage.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
PBIB1214E
PBIB1212E
SERVICE DATA AND SPECIFICATIONS (SDS)
FL-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Tank
INFOID:0000000009950434
Standard and Limit
Fuel tank capacity
Approx. 50.0 (13-1/4 US gal, 11 Imp gal)
Fuel recommendation
Refer to
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Suspension . . . . . . . . . ..
Precautions for Removing of Battery Terminal . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
FRONT COIL SPRING AND STRUT . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
TRANSVERSE LINK . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT STABILIZER . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT SUSPENSION MEMBER . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст