Nissan Cube. Manual — part 935
PRECAUTIONS
STR-23
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009945321
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010138348
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
STR-24
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009945322
Commercial Service Tools
INFOID:0000000009945323
Tool number
(Kent-Moore No.)
Tool name
Description
—
(—) Model GR8-1200 NI
Multitasking battery and electrical di-
agnostic station
Tests batteries, starting and charging sys-
tems and charges batteries.
For operating instructions, refer to diagnos-
tic station instruction manual.
AWIIA1239ZZ
Tool name
Description
Power tool
Loosening bolts, nuts and screws
PIIB1407E
STARTER MOTOR
STR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
REMOVAL AND INSTALLATION
STARTER MOTOR
Exploded View
INFOID:0000000009945324
REMOVAL
DISASSEMBLY
1.
“S” terminal harness
2.
“B” terminal harness
3.
Starter motor
4.
Cylinder block
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
PKIC8095E
STR-26
< REMOVAL AND INSTALLATION >
STARTER MOTOR
Type: S114-955
NOTE:
Apply high-temperature grease to lubricate the bearing, gears and frictional surface when assembling the
starter.
Removal and Installation
INFOID:0000000009945325
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air duct (inlet). Refer to
3.
Remove radiator reservoir tank.
4.
Disconnect oil pressure switch connector.
5.
Remove “B” terminal nut and “B” terminal harness.
6.
Remove “S” terminal nut and “S” terminal harness.
7.
Remove starter motor mounting bolts.
8.
Remove starter motor upward from the vehicle.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Be careful to tighten “B” terminal nut to the specified torque.
JPBIA0549GB
1.
Magnetic switch assembly
2.
Dust cover kit
3.
Shift lever set
4.
Center bracket (A)
5.
Yoke assembly
6.
Armature assembly
7.
Brush holder assembly
8.
Thrust washer
9.
Rear cover assembly
10. Internal gear
11.
Planetary gear
12. Pinion shaft
13. Packing
14. Thrust washer
15. Center bracket (P)
16. E-ring
17. Pinion assembly
18. Pinion stopper
19. Pinion stopper clip
20. Gear case assembly
: High-temperature grease point
: N·m (kg-m, in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст