Nissan Cube. Manual — part 917
ST-10
< REMOVAL AND INSTALLATION >
STEERING WHEEL
Disassembly and Assembly
INFOID:0000000009949816
DISASSEMBLY
1.
Remove steering wheel. Refer to
2.
Remove steering column side cover.
3.
Remove steering switch.
ASSEMBLY
Note the following, and install in the reverse order of removal.
• Securely insert the steering switch into the mounting hole of locating bush for the steering wheel.
STEERING COLUMN
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000009949817
Removal and Installation
INFOID:0000000009949818
REMOVAL
CAUTION:
• Never impact on the axis when removing steering column assembly.
• Place a matching mark on both intermediate shaft and steering column assembly before removing
intermediate shaft.
• Never repeat static steering. (Motor and EPS control unit could be heated.)
• Be careful when removing steering column assembly from the vehicle because it is heavy.
• Keep steering column assembly away from magnetic sources.
• Never disassemble steering column assembly. It is not separable.
1.
Set vehicle to the straight-ahead position.
2.
Place the tilt to the lowest level.
3.
Remove instrument lower panel LH. Refer to
4.
Remove knee protector.
5.
Remove driver air bag module. Refer to
6.
Remove steering wheel. Refer to
7.
Remove steering column cover. Refer to
.
8.
Remove spiral cable. Refer to
.
9.
Remove combination switch. Refer to
(with intelligent key system),
(without intelligent key system).
10. Disconnect each switch harness connectors installed to steering column assembly.
1.
Steering column assembly
2.
Intermediate shaft
Refer to
JSGIA0655GB
ST-12
< REMOVAL AND INSTALLATION >
STEERING COLUMN
11. Remove the intermediate shaft mounting bolt (steering gear side).
CAUTION:
• Place a matching mark on both intermediate shaft and steering gear assembly before removing
intermediate shaft.
• When removing intermediate shaft, never insert a tool, such as a screwdriver, into the yoke
groove to pull out the intermediate shaft. In case of the violation of the above, replace intermedi-
ate shaft with a new one.
12. Remove steering column assembly.
13. Remove brake pedal. Refer to
14. Separate the intermediate shaft from steering column assembly.
CAUTION:
• Place a matching mark on both intermediate shaft and steering column assembly before remov-
ing intermediate shaft.
• When removing intermediate shaft, never insert a tool, such as a screwdriver, into the yoke
groove to pull out the intermediate shaft. In case of the violation of the above, replace intermedi-
ate shaft with a new one.
INSTALLATION
CAUTION:
• Never impact on the axis when removing steering column assembly.
• Be careful when removing steering column assembly from the vehicle because it is heavy.
Note the following, and install in the reverse order of removal.
• Insert bolt in the proper direction. (Do not insert it from the other side.)
• When connecting intermediate shaft lower side and pinion assembly, make sure the bolt is securely seated
in groove of pinion assembly before final tightening.
• When tightening bolt (steering gear assembly side), tighten it by hand first, and make sure there is no feeling
of sticking or galling before final tightening.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft (A) before final tightening.
CAUTION:
• After installing steering column assembly, perform self-diag-
nosis with CONSULT to ensure correct operation. Refer to
.
• Rotate steering wheel to check for decentered condition,
binding, noise or excessive steering effort.
• Adjust neutral position of steering angle sensor. Refer to
Inspection
INFOID:0000000009949819
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Measure steering column assembly rotating torque using a preload
gauge (A) [SST: ST3127S000 (J-25765-A)]. Replace steering col-
umn assembly if the rotating torque is outside the standard.
SGIA1295E
Rotating torque
: Refer to
JPGIA0085ZZ
STEERING COLUMN
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Measure the length “L” shown in the figure, if vehicle has been
involved in a minor collision. Replace steering column assembly
(with motor, reduction gear, sensor) if “L” is outside the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt mechanism operating range “T” shown in the figure.
Steering column length (L)
: Refer to
JSGIA0656ZZ
Tilt operating range (T)
: Refer to
JSGIA0657ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст