Nissan Cube. Manual — part 628
HEADLINING
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Exploded View
INFOID:0000000009949272
Removal and Installation
INFOID:0000000009949273
REMOVAL
1.
Remove front body side welt (LH/RH) and rear body side welt (LH/RH). Refer to
.
2.
Remove front pillar garnish (LH/RH). Refer to
INT-16, "Removal and Installation"
.
1.
Map lamp bracket
2.
Headlining assembly
3.
Map lamp assembly
4.
Inside mirror cover
5.
Sunvisor holder (LH/RH)
6.
Sunvisor assembly (LH/RH)
7.
Room lamp lens
8.
Room lamp assembly
9.
Assist grip
10.
Headlining clip
: Pawl
JMJIA3031ZZ
INT-22
< REMOVAL AND INSTALLATION >
HEADLINING
3.
Disconnect microphone harness connector (A).
4.
Remove center pillar upper garnish (LH/RH). Refer to
INT-16, "Removal and Installation"
5.
Remove luggage side upper finisher (LH/RH). Refer to
INT-24, "Removal and Installation"
6.
Remove sunvisor assembly mounting screws, and then remove sunvisor assembly (LH/RH).
7.
Remove inside mirror cover and then remove inside mirror. Refer to
MIR-15, "Removal and Installation"
8.
Disengage room lamp lens fixing pawls with a remover tool, the
mounting screws and then remove the room lamp. Refer to
109, "Removal and Installation"
9.
Disengage the map lamp fixing pawls with a remover tool and
then remove the map lamp.
10. Remove the assist grips.
• Insert a small minus driver as shown by the arrow in the figure
to disengage the fixing pawls.
• Remove the mounting bolts.
• Pull out the assist grip to remove.
11. Rotate the sunvisor holder (LH/RH) at approximately 90 degrees and then pull it down to remove.
12. Remove the headlining clip located at the rear side with a remover tool.
JMJIA2892ZZ
: Pawl
JMJIA2896ZZ
: Pawl
JMJIA2906ZZ
: Pawl
JMJIA2895ZZ
HEADLINING
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
13. Remove the headlining assembly through the back door.
CAUTION:
• When removing headlining, 2 workers are required. (1 for
the front and rear of headlining)
• Cover center console finisher upper surface with a shop
cloth to prevent it from being damaged.
• Never bend headlining when removing.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never bend headlining when installing.
• When installing, start by installing both sunvisor holders and headlining clips in order to keep the
headlining in position.
JMJIA3032ZZ
INT-24
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000009949274
Removal and Installation
INFOID:0000000009949275
REMOVAL
LUGGAGE REAR PLATE
1.
Fully open back door.
1.
Luggage side upper finisher LH
2.
Luggage side lower finisher clip (LH/
RH)
3.
Luggage side lower finisher LH
4.
Luggage side lower finisher lid (LH/
RH)
5.
Luggage rear plate
6.
Rope hook
7.
Luggage room lamp
8.
Luggage side lower finisher RH
9.
Luggage side upper finisher RH
10. Tonneau cover
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA3536ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст