Nissan Cube. Manual — part 990
TM-216
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CVT SHIFT SELECTOR
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000009949080
Removal and Installation
INFOID:0000000009949081
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal and installation.
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-82, "Removal and Installation"
2.
Shift selector lever knob in “N” position.
3.
Slide knob cover downward.
CAUTION:
Be careful not to damage selector lever knob.
4.
Pull out lock pin from selector lever knob.
5.
Remove selector lever knob and knob cover as a set from selector lever.
CAUTION:
Never press selector button.
6.
Remove center console assembly. Refer to
.
1.
Selector lever knob
2.
Knob cover
3.
Plate
4
CVT shift selector
5.
Park position switch
6.
Position indicator plate
7.
Selector button
8.
Selector button return spring
9.
Lock pin
10.
Overdrive control switch
11.
Dust cover
Refer to
for symbols in the figure.
JSDIA1298GB
CVT SHIFT SELECTOR
TM-217
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Disconnect CVT shift selector connector.
8.
Disconnect key interlock cable from CVT shift selector assembly. Refer to
.
(Without intelligent Key system)
9.
Remove the bolts from the CVT shift selector assembly.
10. Remove exhaust front tube, center muffler and heat plates. Refer to
11. Remove the plate from the CVT shift selector assembly.
12. Remove the lock plate from the control cable. Refer to
.
13. Remove control cable from the CVT shift selector assembly. Refer to
14. Insert flat-bladed screwdrivers at points (A) and (B) as shown,
and press both tabs (E) and (F) at the front (C) and rear (D)
slightly toward the center of the CVT shift selector assembly to
remove the CVT shift selector assembly from the underside of
the vehicle.
15. Remove CVT shift selector assembly from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control cable (1) to CVT shift selector assembly
(2), check that control cable is fully pressed in with the ribbed (A)
surface facing upward.
• Refer to the followings when installing the selector lever knob to
the CVT shift selector assembly.
- Install the lock pin (1) to the selector lever knob (2).
- Install the knob cover (3) to the selector lever knob.
- Shift selector lever in “N” position.
- Insert the shift lever knob into the shift lever until it clicks.
CAUTION:
• Install it straight, and never tap or apply any shock to install
it.
• Never press selector button.
: Vehicle front
SCIA6970E
: Vehicle front
JPDIA0136ZZ
SCIA6972E
TM-218
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CVT SHIFT SELECTOR
Disassembly and Assembly
INFOID:0000000009949082
DISASSEMBLY
1.
Remove overdrive control switch, selector lever button, and selector button return spring from selector
lever knob.
CAUTION:
Be careful not to damage selector lever knob.
2.
Remove dust cover from CVT shift selector assembly.
3.
Insert a flat-bladed screwdriver to (A) (at 4 locations) as shown,
and bend each hook slightly to raise position indicator plate (1)
and remove from CVT shift selector assembly (2).
4.
Remove park position switch (1) from CVT shift selector assem-
bly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Inspection
INFOID:0000000009949083
INSPECTION AFTER INSTALLATION
Check the CVT position. Refer to
TM-215, "Inspection and Adjustment"
.
SCIA6969E
JSDIA1307ZZ
CONTROL CABLE
TM-219
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000009949084
Removal and Installation
INFOID:0000000009949085
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
1.
Remove battery. Refer to
.
2.
Remove air duct (inlet), air duct and air cleaner case. Refer to
.
3.
Remove battery bracket.
4.
Remove control cable fitting nut from control cable.
5.
Remove lock plate from bracket.
6.
Remove control cable from bracket.
7.
Remove control cable from CVT shift selector assembly. Refer to
8.
Remove control cable from vehicle.
9.
Remove bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
CVT shift selector assembly
2.
Bracket
3.
Lock plate
4.
Bracket
5.
Transaxle assembly
6.
Control cable
7.
Lock plate
A.
Manual lever
Refer to
JSDIA1296GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст