Nissan Cube. Manual — part 436
EXL-18
< SYSTEM DESCRIPTION >
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXTERIOR LAMP BATTERY SAVER SYSTEM
System Diagram
INFOID:0000000009945122
WITH INTELLIGENT KEY
WITHOUT INTELLIGENT KEY
System Description
INFOID:0000000009945123
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamp* OFF after a period of time to prevent the battery from over-discharge when the
ignition switch is turned OFF with the exterior lamp ON.
*: Headlamp (LO/HI), parking (front side marker) lamp, tail lamp, license plate lamp, rear side marker lamp and
front fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM activates the timer and turns the exterior lamp OFF 45 seconds after the ignition switch is turned from
ON
→
OFF with the exterior lamps ON.
NOTE:
JPLIA1037GB
JPLIA0740GB
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXL-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Headlamp control function turns the exterior lamps ON normally when the ignition switch is turned ACC or
the engine started (both before and after the exterior lamp battery saver is turned OFF).
• The timer starts at the time that the lighting switch is turned from OFF
→
1ST or 2ND with the exterior lamp
OFF.
Component Parts Location
INFOID:0000000009945124
Component Description
INFOID:0000000009945125
1.
Push switch
(With Intelligent Key)
2.
Key switch
(Without Intelligent Key)
3.
(with Intelligent Key) or
PCS-36, "Component Parts Loca-
tion"
(without Intelligent Key).
4
Combination meter
5.
BCM
Refer to
BCS-95, "Component Parts Loca-
tion"
(without Intelligent Key).
6.
Combination switch
JPLIA1805ZZ
Part
Description
BCM
• Detects each switch condition by the combination switch reading function.
• Activates the battery saver to turn the exterior lamps OFF according to the vehicle
condition.
- Requests each relay OFF to IPDM E/R (with CAN communication).
IPDM E/R
Controls the integrated relay according to the request from BCM (with CAN communi-
cation).
Combination switch
(Lighting & turn signal switch)
Refer to
(with Intelligent Key) or
(without Intelligent Key).
EXL-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010249349
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Automatic air conditioner
AIR CONDITONER
×
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
EXL-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in
the P position (CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000009945127
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”
*
)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK”
*
to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”
*
.) to low power consumption mode
LOCK
Power supply position is “LOCK”
*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст