Nissan Cube. Manual — part 674

MWI-20

< SYSTEM DESCRIPTION >

METER SYSTEM

METER ILLUMINATION CONTROL

METER ILLUMINATION CONTROL : System Diagram

INFOID:0000000009945678

METER ILLUMINATION CONTROL : System Description

INFOID:0000000009945679

METER ILLUMINATION ON/OFF CONTROL FUNCTION

The combination meter receives the following signals to control meter illumination.

Turns ON Condition

Ignition switch ON

Turns OFF Condition

If any of the following conditions is fulfilled.
• During a crank with vehicle speed less than 1 km/h (0.6 MPH)
• Ignition switch OFF or ACC

METER ILLUMINATION CONTROL FUNCTION

• Combination meter is transferred to nighttime mode with position light request signal from BCM via CAN

communication.

• Meter illumination level can be adjusted in following steps using

the illumination control switch (1).

JPNIA1648GB

Signal name

Signal source

Ignition signal

—

Engine status signal
(CAN communication)

ECM

Vehicle speed signal
(CAN communication)

ABS actuator and control unit

(control unit)

Condition

Steps

Daytime mode

22

Nighttime mode

22

JPNIA1665ZZ

MWI

METER SYSTEM

MWI-21

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

METER ILLUMINATION CONTROL : Component Parts Location

INFOID:0000000010235629

METER ILLUMINATION CONTROL : Component Description

INFOID:0000000009945681

JSNIA6649ZZ

1.

Fuel level sensor unit

2.

ABS actuator and electric unit (con-
trol unit)
Refer to

BRC-12, "Component Parts

Location"

.

3.

Ambient sensor
Refer to

HAC-24, "Component Parts

Location"

.

4.

Oil pressure switch
Refer to

EM-86, "Exploded View"

.

5.

A/C auto amp. (auto A/C models)
Refer to

HAC-24, "Component Parts

Location"

.

6.

IPDM E/R
• Refer to

PCS-5, "Component Parts

Location"

(with I-KEY).

• Refer to

PCS-36, "Component

Parts Location"

(without I-KEY).

7.

ECM
Refer to

EC-36,

"Component Parts Location"

.

8.

TCM
Refer to

TM-71, "Component Parts

Location"

.

9.

BCM
Refer to

BCS-10, "Component Parts

Location"

(With intelligent key sys-

tem) or

BCS-95, "Component Parts

Location"

(Without intelligent key sys-

tem).

10. Combination meter

A.

Under of right side rear seat

Unit

Description

Combination meter

Controls the meter illumination with the meter control switch signal from the meter control switch
and the position light request signal from BCM via CAN communication.

ECM

Transmits the engine status signal to the combination meter via CAN communication.

ABS actuator and electric unit
(control unit)

Transmits the vehicle speed signal to the combination meter via CAN communication.

MWI-22

< SYSTEM DESCRIPTION >

METER SYSTEM

METER EFFECT FUNCTION

METER EFFECT FUNCTION : System Diagram

INFOID:0000000009945682

METER EFFECT FUNCTION : System Description

INFOID:0000000009945683

ENGINE-START EFFECT FUNCTION

For CVT Models

When "engine start" is read, the effect of comfort starts only once by turning on combination meter illumination
stepwise and sweeping the needles of speedometer and tachometer.

For M/T Models

When "engine start" is read, the effect of comfort starts only once by turning on combination meter illumination
and start-up lamp stepwise and sweeping the needles of speedometer and tachometer.

Outline of Control System

System control is provided when all of the following conditions are met.

*: For CVT models

NOTE:

The engine-start effect function ends if any one of the above conditions is lost during the activation of this function.

BCM

Transmits the position light request signal to the combination meter via CAN communication.

Combination switch (lighting
switch)

Using the combination switch reading function, BCM reads the combination switch status.

Unit

Description

JPNIA1649GB

Operating condition

Signal name

Signal source

Ignition switch

ON

Ignition signal

—

Shift position

*

P-range

Shift position signal
(CAN communication)

TCM

Engine status

More than 500 rpm

Engine speed signal
(CAN communication)

ECM

Except when cranking

Engine status signal
(CAN communication)

Vehicle speed

Less than 1 km/h (0.6 MPH)

Vehicle speed signal
(CAN communication)

ABS actuator and electric unit

(control unit)

MWI

METER SYSTEM

MWI-23

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

METER EFFECT FUNCTION : Component Parts Location

INFOID:0000000010235632

METER EFFECT FUNCTION : Component Description

INFOID:0000000009945685

JSNIA6649ZZ

1.

Fuel level sensor unit

2.

ABS actuator and electric unit (con-
trol unit)
Refer to

BRC-12, "Component Parts

Location"

.

3.

Ambient sensor
Refer to

HAC-24, "Component Parts

Location"

.

4.

Oil pressure switch
Refer to

EM-86, "Exploded View"

.

5.

A/C auto amp. (auto A/C models)
Refer to

HAC-24, "Component Parts

Location"

.

6.

IPDM E/R
• Refer to

PCS-5, "Component Parts

Location"

(with I-KEY).

• Refer to

PCS-36, "Component

Parts Location"

(without I-KEY).

7.

ECM
Refer to

EC-36,

"Component Parts Location"

.

8.

TCM
Refer to

TM-71, "Component Parts

Location"

.

9.

BCM
Refer to

BCS-10, "Component Parts

Location"

(With intelligent key sys-

tem) or

BCS-95, "Component Parts

Location"

(Without intelligent key sys-

tem).

10. Combination meter

A.

Under of right side rear seat

Unit

Description

Combination meter

Receives signals from each unit with the CAN communication and performs meter effect.

ECM

Transmits engine speed signal and engine status signal to the combination meter via CAN com-
munication.

TCM

Transmits shift position signal to the combination meter via CAN communication.

ABS actuator and electric unit
(control unit)

Transmits vehicle speed signal to the combination meter via CAN communication.