Nissan Cube. Manual — part 995
TM-236
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
TRANSAXLE ASSEMBLY
• Transmission range switch connector
• Primary speed sensor connector
• Secondary speed sensor connector
• Ground
6.
Remove control cable and bracket from transaxle assembly. Refer to
.
7.
Remove CVT water hoses. Refer to
TM-230, "WATER HOSE : Exploded View"
8.
Remove CVT water tubes. Refer to
TM-230, "WATER HOSE : Exploded View"
.
9.
Remove CVT fluid level gauge.
10. Remove CVT fluid charging pipe.
11. Remove O-ring from CVT fluid charging pipe.
12. Remove starter motor. Refer to
.
13. Remove engine under cover.
14. Turn crankshaft, and remove the four tightening nuts for drive plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from the front of the engine.
15. Remove front drive shafts. Refer to
.
16. Remove heat insulator. Refer to
17. Support transaxle assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to collide against drain plug.
18. Remove engine mounting insulator (LH). Refer to
.
19. Remove engine mounting bracket support (LH). Refer to
.
20. Remove rear engine mounting bracket. Refer to
21. Remove rear torque rod. Refer to
.
22. Support engine assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to collide against drain plug.
23. Remove engine mounting bracket (LH). Refer to
.
24. Remove bolts fixing transaxle assembly to engine assembly.
25. Remove transaxle assembly from vehicle.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure transaxle assembly to a transmission jack.
26. Remove CVT fluid cooler tubes. Refer to
TM-231, "CVT FLUID COOLER HOSE : Exploded View"
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply grease to O-ring.
• Check fitting of dowel pins (A) when installing transaxle assembly
to engine assembly.
SCIA6618J
TRANSAXLE ASSEMBLY
TM-237
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Rotate torque converter so that the stud bolt (A) for mounting the
drive plate location guide of torque converter aligns with the
mounting position of starter motor.
• Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the mounting position (B) of
starter motor.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
• Be careful that torque converter stud bolt is aligned to drive
plate hole position. Otherwise stud bolt contacts drive plate.
NOTE:
Insert stud bolt of torque converter into the hole of drive plate,
aligning the drive plate hole position and torque converter.
• Temporally tighten drive plate and torque converter connecting
nuts and tighten to the specified torque.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the front of the engine.
• When tightening the nuts for the torque converter after fixing the crankshaft pulley bolts, confirm
the tightening torque of the crankshaft pulley mounting bolts. Refer to
• When installing transaxle assembly to the engine assembly, attach
the fixing bolts in accordance with the following.
Inspection and Adjustment
INFOID:0000000009949117
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to transaxle assembly, check
dimension “A” within the reference value limit.
JSDIA1303ZZ
: 51 N·m (5.2 kg-m, 38 ft-lb)
Bolt position
A
B
Insertion direction
Transaxle assembly to engine
assembly
Engine assembly to transaxle
assembly
Number of bolts
2
2
Bolt length mm (in)
55 (2.17)
50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)
62.0 (6.3, 45.7)
SCIA6617J
JSDIA1287ZZ
B
: Scale
C
: Straightedge
Dimension “A”
:
JPDIA0682ZZ
TM-238
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
TRANSAXLE ASSEMBLY
INSPECTION AFTER INSTALLATION
Check the following.
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Check CVT position. Refer to
TM-215, "Inspection and Adjustment"
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Perform “ADDITIONAL SERVICE WHEN REPLACE TRANSAXLE ASSEMBLY”. Refer to
.
TORQUE CONVERTER
TM-239
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
TORQUE CONVERTER
Disassembly
INFOID:0000000009949118
1.
Remove transaxle assembly. Refer to
.
2.
Remove torque converter from transaxle assembly.
CAUTION:
Never damage bushing inside of torque converter sleeve when removing torque converter.
Assembly
INFOID:0000000009949119
Note the following, and install in the reverse order of removal.
Attach the pawl (A) of the torque converter to the inner gear hole (B)
on the oil pump side.
CAUTION:
• Rotate the torque converter for installing torque converter.
• Never damage the bushing inside the torque converter sleeve
when installing the converter housing oil seal.
Inspection
INFOID:0000000009949120
INSPECTION AFTER INSTALLATION
After inserting a torque converter to transaxle assembly, check
dimension “A” within the reference value limit.
JPDIA0692ZZ
B
: Scale
C
: Straightedge
Dimension “A”
:
JPDIA0682ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст