Nissan Cube. Manual — part 401
EM-8
< PRECAUTION >
PRECAUTIONS
• After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
PREPARATION
EM-9
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009944913
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing oil pan (upper and lower) etc.
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
(
—
)
Adapter
Disassembling and assembling valve mecha-
nism
Part (1) is a component of KV10116200 (J-
26336-A), but Part (2) is not so.
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for main bearing cap, cylinder
head, etc.
KV10117100
(J-3647-A)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor 1
For 22 mm (0.87 in) width hexagon nut
KV10107902
(J-38959)
Valve oil seal puller
Removing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A (G).
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
H: Side B
Unit: mm (in)
S-NT046
PBIC1650E
S-NT014
NT379
NT011
JPBIA0396ZZ
EM-10
< PREPARATION >
PREPARATION
Commercial Service Tools
INFOID:0000000009944914
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pilot bushing puller
Removing pilot converter
KV11103000
(
—
)
Pulley puller
Removing crankshaft pulley
KV11105210
(J-44716)
Stopper plate
Fixing drive plate
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT044
S-NT045
NT676
ZZA0009D
(Kent-Moore No.)
Tool name
Description
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room
(
—
)
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
PBIC0198E
JPBIA0399ZZ
PREPARATION
EM-11
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
(
—
)
Pulley holder
Crankshaft pulley removing and installing
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
(
—
)
Piston ring expander
Removing and installing piston ring
(
—
)
Valve guide drift
Removing and installing valve guide
(
—
)
Valve guide reamer
1: Reaming valve guide inner hole
2: Reaming hole for oversize valve guide
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new air fuel ratio sensor
(Use with anti-seize lubricant shown below.)
A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
C: Mating surface shave cylinder
D: Flutes
(
—
)
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
(Kent-Moore No.)
Tool name
Description
ZZA1010D
S-NT048
S-NT030
PBIC4012E
PBIC4013E
JPBIA0238ZZ
AEM489
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст