Nissan Cube. Manual — part 963
TM-108
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
P0703 BRAKE SWITCH B
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
7.
DETECT MALFUNCTIONING ITEMS
Check the following.
• 10A fuse (No.9)
• Harness for short or open between battery and stop lamp switch (Refer to
• Battery
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
(With intelligent key system),
(Without intelligent key system).
NO
>> Repair or replace damaged parts.
Component Inspection (Stop Lamp Switch)
INFOID:0000000009948955
1.
CHECK STOP LAMP SWITCH
Check continuity between stop lamp switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
Stop lamp switch connector
Condition
Continuity
Connector
Terminal
E115
1
2
Depressed brake pedal
Existed
Brake pedal not depressed
Not existed
3
4
Depressed brake pedal
Existed
Brake pedal not depressed
Not existed
P0705 TRANSMISSION RANGE SWITCH A
TM-109
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0705 TRANSMISSION RANGE SWITCH A
Description
INFOID:0000000009948956
• Transmission range switch is installed to upper part of transaxle case.
• Transmission range switch detects the selector lever position and transmits selector lever position signal to
TCM.
DTC Logic
INFOID:0000000009948957
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Start the engine.
2.
Shift and hold selector lever to each position for 5 seconds or more.
3.
Select “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT”.
Is “P0705” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009948958
1.
CHECK TRANSMISSION RANGE SWITCH POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between transmission range switch vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
DTC
Trouble diagnosis name
DTC is detected if...
Possible cause
P0705
Transmission Range Sensor A
Circuit (PRNDL Input)
• Range signal is not transmitted to TCM
• 2 or more range signals are transmitted to
TCM
• Harness or connectors
[Transmission range switch circuit is open
or shorted.]
• Transmission range switch
Transmission range switch vehicle side harness connector
Ground
Condition
Voltage (Approx.)
Connector
Terminal
F21
3
Ignition switch: ON
Battery voltage
Ignition switch: OFF
0 V
TM-110
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
P0705 TRANSMISSION RANGE SWITCH A
3.
Check continuity between TCM vehicle side harness connector terminals and transmission range switch
vehicle side harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 2)
Check continuity between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TRANSMISSION RANGE SWITCH
1.
Remove control cable from manual lever. Refer to
.
2.
Check transmission range switch. Refer to
TM-111, "Component Inspection (Transmission Range
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Transmission range switch is malfunctioning. Replace transaxle assembly. Refer to
.
5.
CHECK HARNESS BETWEEN TRANSMISSION RANGE SWITCH AND IPDM E/R (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between transmission range switch vehicle side harness connector terminals and IPDM
E/R vehicle side harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK HARNESS BETWEEN TRANSMISSION RANGE SWITCH AND IPDM E/R (PART 2)
Check continuity between transmission range switch vehicle side harness connector terminal and ground.
TCM vehicle side harness connector
Transmission range switch vehicle side harness
connector
Continuity
Connector
Terminal
Connector
Terminal
E18
18
F21
4
Existed
22
5
E19
26
6
43
7
44
8
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
E18
18
Not existed
22
E19
26
43
44
Transmission range switch vehicle side harness
connector
IPDM E/R vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F21
3
E15
58
Existed
P0705 TRANSMISSION RANGE SWITCH A
TM-111
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
DETECT MALFUNCTIONING ITEMS
Check the following.
• IPDM E/R
• 10A fuse (No.55, located in the IPDM E/R)
• Harness for short or open between IPDM E/R and ignition switch (Refer to
PG-33, "Wiring Diagram - IGNI-
.)
• Ignition switch
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
Component Inspection (Transmission Range Switch)
INFOID:0000000009948959
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity of transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Transmission range switch is malfunctioning. Replace transaxle assembly. Refer to
Transmission range switch vehicle side harness connector
Ground
Continuity
Connector
Terminal
F21
3
Not existed
Transmission range switch connector
Condition
Continuity
Connector
Terminal
F21
1
2
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
3
4
Manual lever: “P” position
Existed
Other than the above
Not existed
3
5
Manual lever: “R” position
Existed
Other than the above
Not existed
3
6
Manual lever: “N” position
Existed
Other than the above
Not existed
3
7
Manual lever: “D” position
Existed
Other than the above
Not existed
3
8
Manual lever: “L” position
Existed
Other than the above
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст