Nissan Cube. Manual — part 696
PCS
POWER CONSUMPTION CONTROL SYSTEM
PCS-9
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Component Parts Location
INFOID:0000000010269398
1.
Combination meter
2.
IPDM E/R
Refer to
3.
JPMIA1549ZZ
PCS-10
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000009944995
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamps
• Side marker lamp
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5.
The oil pressure warning lamp starts blinking when the auto active test starts.
6.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system. Refer to
.
• Do not start the engine.
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
Operation
sequence
Inspection location
Operation
A
Oil pressure warning lamp
Blinks continuously during operation of auto active test
1
Rear window defogger
10 seconds
2
Front wiper
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamps
• Side marker lamps
• License plate lamps
• Tail lamps
• Front fog lamps
10 seconds
4
Headlamps
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
LO for 5 seconds
→
HI for 5 seconds
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-11
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JPMIA1486GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger
ground circuit
• Harness or connector be-
tween IPDM E/R and rear
window defogger
• IPDM E/R
Any of the following components do not operate
• Parking lamps
• Side marker lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (HI, LO)
• Front wiper (HI, LO)
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground cir-
cuit
• Harness or connector be-
tween IPDM E/R and appli-
cable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal
between A/C amp. and
ECM
• CAN communication signal
between ECM and IPDM E/
R
NO
• Magnet clutch
• Harness or connector be-
tween IPDM E/R and mag-
net clutch
• IPDM E/R
PCS-12
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000009944996
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Oil pressure warning lamp does not operate
Perform auto active test.
Does the oil pressure warning
lamp blink?
YES
• Harness or connector be-
tween IPDM E/R and oil
pressure switch
• Oil pressure switch
• IPDM E/R
NO
• CAN communication signal
between IPDM E/R and
BCM
• CAN communication signal
between BCM and combi-
nation meter
• Combination meter
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal
between ECM and IPDM E/
R
NO
• Cooling fan motor
• Harness or connector be-
tween IPDM E/R and cool-
ing fan motor
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст