Nissan Cube. Manual — part 684
MWI-60
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
JRNWD0652GB
MWI
COMBINATION METER
MWI-61
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Fail-Safe
INFOID:0000000009945725
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
JRNWD0653GB
MWI-62
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
DTC Index
INFOID:0000000009945726
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control
When suspending communication, changes to nighttime mode.
Shift position indicator
The indicator turns OFF by suspending communication.
Information display
Instantaneous fuel warning
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition is
indicated.
Average fuel consumption
Possible driving distance
Average vehicle speed
Low tire pressure warning
The display turns OFF by suspending communication.
Buzzer
The buzzer turns off by suspending communication.
Warning lamp/indicator lamp
ABS warning lamp
The lamp turns ON by suspending communication.
VDC warning lamp
EPS warning lamp
Brake warning lamp
Malfunction indicator lamp
Low tire pressure warning lamp
The lamp turns ON after flashing for 1 minute.
VDC OFF indicator lamp
The lamp turns OFF by suspending communication.
High beam indicator lamp
Turn signal indicator lamp
Door warning lamp
Light indicator lamp
Engine start operation indicator lamp
Shift P warning lamp
Oil pressure warning lamp
CRUISE indicator lamp
O/D OFF indicator lamp
Key warning lamp
Display contents of CONSULT
Diagnostic item is detected when ...
Refer to
CAN COMM CIRCUIT
[U1000]
When combination meter is not transmitting or receiving CAN communication signal
for 2 seconds or more.
CONTROL UNIT (CAN)
[U1010]
When detecting error during the initial diagnosis of the CAN controller of combina-
tion meter.
VEHICLE SPEED
[B2205]
The abnormal vehicle speed signal is input from the ABS actuator and electric unit
(control unit) for 2 seconds or more.
ENGINE SPEED
[B2267]
If ECM continuously transmits abnormal engine speed signals for 2 seconds or
more.
WATER TEMP
[B2268]
If ECM continuously transmits abnormal engine coolant temperature signals for 60
seconds or more.
MWI
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
MWI-63
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
WITH INTELLIGENT KEY
WITH INTELLIGENT KEY : Reference Value
INFOID:0000000010247955
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Condition
Value/Status
MOTOR FAN REQ
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
1/2/3/4
AC COMP REQ
Engine running
A/C switch OFF
Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ
Lighting switch OFF
Off
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated)
On
HL LO REQ
Lighting switch OFF
Off
Lighting switch 2ND, HI or AUTO (Light is illuminated)
On
HL HI REQ
Lighting switch OFF
Off
Lighting switch HI
On
FR FOG REQ
Lighting switch 2ND or
AUTO (Light is illuminated)
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
Stop
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally
Off
Front wiper stops at fail-safe opera-
tion
BLOCK
IGN RLY1 -REQ
Ignition switch OFF or ACC
Off
Ignition switch ON
On
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
PUSH SW
Release the push-button ignition switch
Off
Press the push-button ignition switch
On
INTER/NP SW
Ignition switch ON
• Selector lever in any position oth-
er than P or N (CVT models)
• Release clutch pedal (M/T mod-
els)
Off
• Selector lever in P or N position
(CVT models)
• Depress clutch pedal (M/T mod-
els)
On
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст