Nissan Cube. Manual — part 271
DLK-350
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009950795
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge (upper)
6.
Front door hinge (lower)
7.
Rear door hinge (upper)
8.
Rear door hinge (lower)
9.
Door striker
10.
TORX bolt
Refer to
for symbols in the figure.
JMKIA3837GB
REAR DOOR
DLK-351
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
1.
Remove center pillar garnish (upper/lower). Refer to
INT-16, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install center pillar garnish (upper/lower). Refer to
INT-16, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000009950796
DOOR STRIKER : Removal and Installation
INFOID:0000000009950797
REMOVAL
Remove TORX bolts, and then remove door striker.
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Rear door – Body side outer
C – C
3.5 – 5.5 (0.138 – 0.217)
-1.0 – 1.0 (-0.039 – 0.039)
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen (upper)
6.
Sealing screen (lower)
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
for symbols in the figure.
JMKIA3957ZZ
DLK-352
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000009950798
DOOR HINGE : Removal and Installation
INFOID:0000000009950799
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-349, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove center pillar garnish (upper/lower). Refer to
INT-16, "Removal and Installation"
.
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen (upper)
6.
Sealing screen (lower)
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3957ZZ
REAR DOOR
DLK-353
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000009950800
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009950801
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Fully close the rear door window.
3.
Remove rear door speaker. Refer to
AV-64, "Removal and Installation"
(AUDIO WITHOUT NAVIGATION)
AV-135, "Removal and Installation"
(AUDIO WITH NAVIGATION).
4.
Remove mounting bolts of the check link on the vehicle.
5.
Remove mounting bolts of the check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check rear door open/close operation after installation.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen (upper)
6.
Sealing screen (lower)
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
for symbols in the figure.
JMKIA3957ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст