Nissan Cube. Manual — part 693
PARKING BRAKE SYSTEM
PB-3
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
Inspection and Adjustment
INFOID:0000000009949249
INSPECTION
Lever Stroke
1.
Operate the parking brake lever with a force of 196 N (20 kg, 44 lb). Check that the lever stroke is within
the specified number of notches. (Check it by listening to the clicks of the ratchet.)
2.
When brake warning lamp turns ON, check that the lever stroke is within the specified number of notches.
(Check it by listening to the clicks of the ratchet.)
Inspect Components
• Check each component for installation condition such as looseness.
• Check the parking brake lever assembly for bend, damage and cracks. Replace if necessary.
• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.
• Check the parking brake switch, and replace it if necessary. Refer to
BRC-79, "Component Inspection"
ADJUSTMENT
1.
Remove the console mask. Refer to
2.
Pull parking brake lever until a socket wrench can be inserted to
adjusting nut (1).
3.
Release the parking brake lever by turning the adjusting nut with
a socket wrench and loosening the cable.
4.
Depress the brake pedal with a force of 196 N (20 kg, 44 lb)
about 10 times and adjust the brake shoe clearance.
CAUTION:
Make sure to securely depress the brake pedal.
5.
Check a drag of rear drum brake. Refer to
6.
Adjust the cable with the following procedure.
a.
When replace parking brake cable, operate the parking brake lever with a force of 490 N (50 kg, 110 lb) for
10 strokes or more.
b.
Adjust the parking brake lever stroke by turning the adjusting nut with a deep socket wrench.
CAUTION:
Never reuse the adjusting nut if the nut is removed.
c.
Operate the parking brake lever with a force of 196 N (20 kg, 44lb). Check that the lever stroke is within
the specified number of notches. (Check it by listening to the clicks of the ratchet.)
d.
Rotate the brake drum with the parking brake lever released and check that there is no drag. Refer to
41, "Inspection and Adjustment"
.
Number of notches
: Refer to
Number of notches
: Refer to
Number of notches
: Refer to
JPFIB0049ZZ
PB-4
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000009949250
Removal and Installation
INFOID:0000000009949251
REMOVAL
1.
Remove rear tires with power tool.
2.
Remove the center console assembly. Refer to
3.
Disconnect the parking brake switch harness connector.
4.
Remove adjusting nut and loosen front cable.
5.
Remove the parking brake lever assembly.
6.
Separate front cable from rear cable, and remove front cable.
7.
Remove the center muffler. Refer to
.
8.
Remove brake shoe, and remove rear cable from operating lever. Refer to
.
9.
Remove rear cable mounting bolts, pull out rear cable from vehicle.
INSTALLATION
Note the following, install in the reverse order of the removal.
• Never reuse adjusting nut.
1.
Parking brake lever assembly
2.
Adjusting nut
3.
Parking brake switch
4.
Front cable
5.
Rear cable (LH)
6.
Rear cable (RH)
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JPFIB0070GB
PARKING BRAKE CONTROL
PB-5
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
Adjustment
INFOID:0000000009949252
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake lever stroke. Refer to
PB-6
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Parking Brake Control
INFOID:0000000009949253
Item
Standard
Number of notches [under force of 196 N (20 kg, 44 lb)]
10
−
11 notches
Number of notches when brake warning lamp turns ON
1 notch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст