Nissan Cube. Manual — part 590
HAC-198
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
INSUFFICIENT COOLING
INSUFFICIENT COOLING
Description
INFOID:0000000009951100
Symptom
• Insufficient cooling
• No cool air comes out. (Air flow volume is normal.)
Diagnosis Procedure
INFOID:0000000009951101
CAUTION:
Perform the self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction
result or DTC is detected, perform the corresponding diagnosis.
1.
CHECK MAGNET CLUTCH OPERATION
1.
Turn the ignition switch ON.
2.
Turn the fan control dial ON.
3.
Press the A/C switch.
4.
Check that the indicator of the A/C switch turns ON. Check visually and by sound that the compressor
operates.
5.
Press the A/C switch again.
6.
Check that the indicator of the A/C switch turns OFF. Check that the compressor stops.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform the diagnosis of “COMPRESSOR DOSE NOT OPERATE” in “SYMPTOM DIAGNOSIS”.
HAC-200, "Diagnosis Procedure"
2.
CHECK DRIVE BELT
Check tension of the drive belt. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjust or replace drive belt depending on the inspection results.
3.
CHECK REFRIGERANT CYCLE PRESSURE
Connect the recovery/recycling recharging equipment to the vehicle and perform the pressure inspection with
the gauge. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace parts depending on the inspection results.
4.
CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of the air conditioner system for leakage.
Is the inspection result normal?
YES
>> Check the air mix door cable installation and air mix door operation.
NO
>> Repair or replace parts depending on the inspection results.
INSUFFICIENT HEATING
HAC-199
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
INSUFFICIENT HEATING
Description
INFOID:0000000009951102
Symptom
• Insufficient heating
• No warm air comes out. (Air flow volume is normal.)
Diagnosis Procedure
INFOID:0000000009951103
CAUTION:
Perform the self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction
result or DTC is detected, perform the corresponding diagnosis.
1.
CHECK COOLING SYSTEM
1.
Check the engine coolant level and check for leakage. Refer to
2.
Check the radiator cap. Refer to
CO-12, "RADIATOR CAP : Inspection"
3.
Check the water flow sounds of the engine coolant. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refill the engine coolant and repair or replace the parts depending on the inspection results.
2.
CHECK HEATER HOSE
Check the installation of heater hose by visually or touching.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace parts depending on the inspection results.
3.
CHECK HEATER CORE
1.
Check the temperature of inlet hose and outlet hose of heater core.
2.
Check that the inlet side of heater core is hot and the outlet side is slightly lower than/almost equal to the
inlet side.
CAUTION:
Always perform the temperature inspection in a short period of time because the engine coolant
temperature is very hot.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the heater core. Refer to
HA-44, "Exploded View (Manual Air Conditioner)"
.
4.
CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of the air conditioner system for air leakage.
Is the inspection result normal?
YES
>> Check the air mix door cable installation and air mix door operation.
NO
>> Repair or replace parts depending on the inspection results.
HAC-200
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
COMPRESSOR DOSE DOT OPERATE
COMPRESSOR DOSE DOT OPERATE
Description
INFOID:0000000009951104
SYMPTOM
Compressor dose not operate.
Diagnosis Procedure
INFOID:0000000009951105
CAUTION:
• Perform the self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction
result or DTC is detected, perform the corresponding diagnosis.
• Check that the refrigerant is enclosed in cooler cycle normally. If the refrigerant amount is shortage
from proper amount, perform the inspection of refrigerant leakage
1.
CHECK A/C INDICATOR
1.
Turn the ignition switch ON.
2.
Operate the blower motor.
3.
Check that A/C indicator is turned ON when pressing the A/C switch.
4.
Check that A/C indicator is turned OFF when pressing the A/C switch again.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK MAGNET CLUTCH OPERATION
Check the magnet clutch. Refer to
HAC-158, "Component Function Check"
.
Does it operate normally?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REFRIGERANT PRESSURE SENSOR
Check the refrigerant pressure sensor. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK BCM OUTPUT SIGNAL
With CONSULT
Check the “A/C ON SIG” or “FAN ON SIG” or “A/C RELAY SIG” in ECM.
Is the inspection result normal?
YES
>> Replace the IPDM E/R. Refer to
NO
.
5.
CHECK A/C SWITCH
Check the A/C switch. Refer to
HAC-159, "Diagnosis Procedure"
Is inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK BLOWER FAN ON SIGNAL
Monitor item
Condition
Status
COMP REQ SIG
A/C switch: OFF
Off
A/C switch: ON
On
FAN REQ SW
Fan control dial: OFF
Off
Fan control dial: ON
On
COMPRESSOR DOSE DOT OPERATE
HAC-201
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Check the blower fan ON signal. Refer to
HAC-165, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts
7.
CHECK THERMO CONTROL AMP.
Check the thermo control amp. Refer to
HAC-151, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
.
NO
>> Repair or replace the malfunctioning parts
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст