Nissan Cube. Manual — part 75
BCS
BCM (BODY CONTROL MODULE)
BCS-149
< ECU DIAGNOSIS INFORMATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Fail-safe
INFOID:0000000009949797
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JRMWE7831GB
BCS-150
< ECU DIAGNOSIS INFORMATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper auto stop signal.
When the rear wiper auto stop signal does not change more than 5 seconds while driving the rear wiper, BCM
stops power supply to protect the rear wiper motor.
Condition of cancellation
1.
Pass more than 1 minute after the rear wiper stop.
2.
Turn rear wiper switch OFF.
3.
Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart
INFOID:0000000009949798
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC Index
INFOID:0000000009949799
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF
→
ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition switch OFF
→
ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF
→
ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT
Fail-safe
Cancellation
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→
OFF
Priority
DTC
1
• U1000: CAN COMM
• U1010: CONTROL UNIT (CAN)
2
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
3
C1735: IGN CIRCUIT OPEN
4
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1729: VHCL SPEED SIG ERR
BCS
BCM (BODY CONTROL MODULE)
BCS-151
< ECU DIAGNOSIS INFORMATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONSULT display
Fail-safe
Tire pressure
monitor warn-
ing lamp ON
Reference
U1000: CAN COMM
—
—
U1010: CONTROL UNIT (CAN)
—
—
B2190: NATS ANTENNA AMP
×
—
B2191: DIFFERENCE OF KEY
×
—
B2192: ID DISCORD BCM-ECM
×
—
B2193: CHAIN OF BCM-ECM
×
—
B2195: ANTI SCANNING
×
—
C1704: LOW PRESSURE FL
—
×
C1705: LOW PRESSURE FR
—
×
C1706: LOW PRESSURE RR
—
×
C1707: LOW PRESSURE RL
—
×
C1708: [NO DATA] FL
—
×
C1709: [NO DATA] FR
—
×
C1710: [NO DATA] RR
—
×
C1711: [NO DATA] RL
—
×
C1716: [PRESS DATA ERR] FL
—
×
C1717: [PRESS DATA ERR] FR
—
×
C1718: [PRESS DATA ERR] RR
—
×
C1719: [PRESS DATA ERR] RL
—
×
C1729: VHCL SPEED SIG ERR
—
×
C1735: IGN CIRCUIT OPEN
—
—
BCS-152
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010166644
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010166647
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
SEF289H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст