Nissan Cube. Manual — part 909
B1209 FRONTAL COLLISION DETECTION
SRC-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1209 FRONTAL COLLISION DETECTION
Description
INFOID:0000000009946289
The air bags and seat belt pre-tensioners for driver and passenger are activated by the air bag diagnosis sen-
sor unit signal transmitted at the time of the frontal collision.
DTC Logic
INFOID:0000000009946290
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-153, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946291
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-5, "FOR FRONTAL COLLISION : When SRS is activated in a colli-
SR-6, "FOR FRONTAL COLLISION : When SRS is not activated in a collision"
.
Is collision diagnosis complete?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC.Refer to
.
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1209
FRONTAL COLLISION
DETECTION
Seat belt pre-tensioner, driver side air bag and pas-
senger air bag are deployed
—
SRC-154
< DTC/CIRCUIT DIAGNOSIS >
B1210 SIDE COLLISION DETECTION
B1210 SIDE COLLISION DETECTION
Description
INFOID:0000000009946292
The side air bag and curtain air bag are activated by the air bag diagnosis sensor unit signal transmitted at the
time of side collision.
DTC Logic
INFOID:0000000009946293
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-154, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946294
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision"
.
Is collision diagnosis complete?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC.Refer to
.
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1210
SIDE COLLISION DE-
TECTION
Side air bag and curtain air bag are deployed
—
B1211 ROLLOVER DETECTION
SRC-155
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1211 ROLLOVER DETECTION
Description
INFOID:0000000009946295
The seat belt pre-tensioner and curtain air bag are activated by the air bag diagnosis sensor unit signal at the
time of rollover.
DTC Logic
INFOID:0000000009946296
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-155, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946297
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
or
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision"
Is collision diagnosis complete?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC.Refer to
.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1211
ROLLOVER DETEC-
TION
Seat belt pre-tensioner and curtain air bag module
are deployed because of rollover detection
—
SRC-156
< DTC/CIRCUIT DIAGNOSIS >
B1212, B1213, B1214 SATELLITE SENSOR RH
B1212, B1213, B1214 SATELLITE SENSOR RH
Description
INFOID:0000000009946298
Satellite sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle side colli-
sion that is more than the specified limit is detected.
DTC Logic
INFOID:0000000009946299
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-156, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946300
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor RH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1212
B1213
B1214
RH1 SAT-SENS
Satellite sensor RH is malfunctioning
• Disconnection of wiring harness
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст