Nissan Cube. Manual — part 141
CHG-30
< REMOVAL AND INSTALLATION >
ALTERNATOR
REMOVAL AND INSTALLATION
ALTERNATOR
Exploded View
INFOID:0000000009945416
REMOVAL
DISASSEMBLY
Type: A002TJ0581
1.
Alternator connector
2.
Alternator mounting bolt (upper)
3.
Alternator mounting bolt (lower)
4.
Alternator
5.
“B” terminal harness
6.
“B” terminal nut
: N·m (kg-m, ft-lb)
JMMIA0534GB
JPMIA0204GB
CHG
ALTERNATOR
CHG-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Removal and Installation
INFOID:0000000009945417
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove drive belt. Refer to
EM-13, "Removal and Installation"
.
3.
Remove radiator reservoir tank.
4.
Remove engine cover.
5.
Remove engine cover clamp bolt (A), and engine cover clamp.
6.
Remove “B” terminal nut (B) and “B” terminal harness.
7.
Disconnect alternator connector (1).
8.
Remove alternator mounting bolt (upper) (C).
9.
Completely loosen alternator mounting bolt (lower) (D), and pull
it out until the bolt head is in contact with the side member. And
then, remove the alternator by pulling it forward.
NOTE:
The alternator can be removed together with the bolts by pulling
it forward and using the alternator bracket bolt hole cutout.
10. Remove alternator upward from the vehicle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Temporarily tighten the alternator bolts in order from the lower to the upper, and then tighten them in
order from the upper to the lower.
For the alternator, the front side (pulley side) surface is the reference surface. Fit the reference sur-
face to the alternator mounting part, and then tighten the bolts.
• Install alternator, and check tension of belt. Refer to
• Be careful to tighten “B” terminal nut to the specified torque.
• For this model, the power generation voltage variable control system that controls the power gener-
ation voltage of the alternator has been adopted. Therefore, the power generation voltage variable
control system operation inspection should be performed after replacing the alternator, and then
make sure that the system operates normally. Refer to
CHG-28, "Inspection Procedure"
Inspection
INFOID:0000000009945418
ALTERNATOR PULLEY INSPECTION
Perform the following.
• One-way clutch pulley check.
CAUTION:
Be careful not to damage rotor
NOTE:
Secure rotor using suitable tool and a rolled shop towel.
1.
Rear bearing
2.
Rotor assembly
3.
Retainer
4.
Front bearing
5.
Front bracket assembly
6.
Pulley
7.
Pulley cap
8.
Stator assembly
9.
IC voltage regulator assembly
10. Diode assembly
11.
Rear bracket assembly
12. Terminal set
13. “B” terminal nut
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSMIA0111ZZ
CHG-32
< REMOVAL AND INSTALLATION >
ALTERNATOR
1.
Check for locking; (Outer ring is turned clockwise when viewed
from front.)
• If it rotates in both directions, replace pulley.
2.
Check for dragging. (Outer ring is turned counterclockwise when
viewed from front.)
• If it locks or unusual resistance is felt, replace pulley.
SKIB0529E
CHG
SERVICE DATA AND SPECIFICATIONS (SDS)
CHG-33
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Alternator
INFOID:0000000009945419
*: Adjustment range of power generation voltage variable control is 11.4 - 15.6 V.
Type
A002TJ0581
MITSUBISHI make
Nominal rating
[V - A]
12 -110
Ground polarity
Negative
Minimum revolution under no-load (When 13.5 V is ap-
plied)
[rpm]
Less than 1,300
Hot output current (When 13.5 V is applied)
[A/rpm]
More than 95/2,500
More than 116/5,000
Regulated output voltage
[V]
14.1 - 14.7
*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст