Nissan Cube. Manual — part 633
INSTRUMENT PANEL ASSEMBLY
IP-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
REMOVAL AND INSTALLATION
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000009949286
JSJIA0095GB
IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000009949287
WORK STEP
When removing instrument panel assembly, combination meter, audio unit (audio mask), cup holder, or center
console assembly take steps in the order shown by the numbers below.
1.
Front passenger air bag module
2.
Instrument panel assembly
3.
Instrument side finisher LH
4.
Cup holder
5.
Cluster lid A (front)
6.
Combination meter
7.
Cluster lid A (rear)
8.
Steering column upper cover
9.
Steering column lower cover
10. Steering lock escutcheon
11.
Hook cover
12. Knob
13. Hook
14. A/C finisher (auto A/C)
15. Glove box assembly
16. Glove box lock
17. Glove box lock cover
18. Glove box cover
19. Glove box damper
20. Instrument side finisher RH
21. Instrument mask
22. Optical sensor
23. Sunload sensor
24. Switch panel finisher
25. Knee protector
26. Instrument lower panel LH
27. Audio unit
28. Cluster lid C
29. A/C finisher (manual A/C)
30. A/C controller (manual A/C)
31. USB connector
32. Instrument lower cover
33. Instrument lower cover bracket
34. Ring
35. Inner socket
36. Power socket finisher
37. Audio mask
38. Instrument lower cover LH
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
PARTS
INSTRUMENT
PANEL
ASSEMBLY
COMBINATION
METER
AUDIO UNIT,
NAVI CONTROL
UNIT,
AUDIO MASK
CUP HOLDER
CENTER
CONSOLE
Shift knob (MT models)
[1]
[1]
Front console cover
[2]
[2]
Rear console cover
[3]
[3]
Console mask
[4]
[4]
Center console assembly
[5]
[5]
Instrument side finisher LH
[6]
[1]
Instrument lower panel LH
[7]
[2]
Knee protector
[8]
Cup holder
[3]
Driver air bag module
[9]
Steering wheel
[10]
Steering lock escutcheon
[11]
Steering column upper cover
[12]
[1]
Steering column lower cover
[13]
Lighting & turn signal switch
[14]
Wiper and washer switch
[15]
Cluster lid A (rear)
[16]
[2]
Combination meter
[17]
[3]
Cluster lid A (front)
[18]
Front body side welt LH
[19]
Front pillar garnish LH
[20]
A/C finisher
[21]
[1]
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
[ ]: Number indicates step in removal procedure.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Put selector lever in [N] position (CVT models).
2.
Remove shift knob (MT models). Refer to
TM-19, "Removal and Installation"
.
3.
Remove front console cover.
1.
Remove front console cover with a flat-bladed screwdriver
(A) wrapped in a tape.
2.
Pull up front console cover.
4.
Remove mounting nut of center console front side.
5.
Remove rear console cover.
1.
Remove rear console cover with hook and pick tool (A) as
shown in the figure.
2.
Pull up rear console cover.
6.
Remove mounting nuts of center console rear side.
A/C control fixing screws
(manual A/C)
[22]
Cluster lid C
[23]
[2]
Audio unit, NAVI control unit,
audio mask
[24]
[3]
Switch panel finisher
[25]
Instrument lower cover LH
[26]
Instrument lower cover
[27]
Instrument mask
[28]
Glove box cover assembly
[29]
Instrument side finisher RH
[30]
Passenger air bag module
[31]
Front body side welt RH
[32]
Front pillar garnish RH
[33]
Instrument panel assembly
[34]
: Pawl
JMJIA3067ZZ
: Pawl
JMJIA3068ZZ
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
7.
Insert a deep-well socket wrench (A) to rotate adjusting nut to
loosen cable sufficiently. Refer to
8.
Remove console mask.
1.
Pull upward to release console mask fixing clips from center
console with remover tool (A).
2.
Disconnect seat heated switch harness connectors. (with
seat heater)
9.
Lift up center console assembly back side, and then remove center console assembly.
10. Remove instrument side finisher LH.
Insert finger into instrument side finisher LH hole. Disengage the
pawls while pulling in lateral direction, and pull back.
CAUTION:
Disengage slowly so that pawls of instrument side finisher
LH are not damaged.
11. Remove instrument lower panel LH.
1.
Remove hood opener and fuel lid opener lever. Refer to
DLK-210, "Removal and Installation"
(with
Intelligent Key System) or
DLK-363, "Removal and Installation"
(without Intelligent Key System).
2.
Remove fixing screw (A).
3.
Pull back instrument lower panel LH.
4.
Disconnect harness connectors, harness clip.
5.
Release data link connector (pawls) then remove it from
instrument lower panel LH.
JMJIA3069ZZ
: Clip
JMJIA3070ZZ
: Pawl
JMJIA3046ZZ
: Pawl
: Metal clip
JMJIA3047ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст