Nissan Cube. Manual — part 877
DIAGNOSIS SYSTEM (OCCUPANT DETECTION SYSTEM)
SRC-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
DIAGNOSIS SYSTEM (OCCUPANT DETECTION SYSTEM)
CONSULT Function
INFOID:0000000009946096
ZERO POINT RESET DESCRIPTION
This vehicle adopts occupant detection system with a weight detecting method. When replacing, or removing
and installing passenger seat, always perform “zero point rest” so that the vehicle recognizes zero point.
If zero point reset is incomplete, occupant detection sensor does not operate normally.
WORK SUPPORT
Monitor item
Description
Zero point reset function
Perform zero point reset. Refer to
SET : Special Repair Requirement"
.
SRC-26
< DTC/CIRCUIT DIAGNOSIS >
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
DTC/CIRCUIT DIAGNOSIS
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000009946097
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic
INFOID:0000000009946098
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946099
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1001
B1002
B1003
B1004
B1005
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
SRC-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-28
< DTC/CIRCUIT DIAGNOSIS >
B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT
B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000009946100
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic
INFOID:0000000009946101
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self-Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946102
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1006
B1007
B1008
B1009
B1010
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст