Nissan Cube. Manual — part 900
B1132 SIDE AIR BAG MODULE RH
SRC-117
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE SIDE AIR BAG MODULE
1.
Replace side air bag module RH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-118
< DTC/CIRCUIT DIAGNOSIS >
B1134 SIDE AIR BAG MODULE LH
B1134 SIDE AIR BAG MODULE LH
Description
INFOID:0000000009946235
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
INFOID:0000000009946236
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-118, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946237
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1134
SIDE MODULE LH
[OPEN]
Side air bag module LH circuit is open
• Disconnection of wiring harness and open
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit
B1134 SIDE AIR BAG MODULE LH
SRC-119
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE SIDE AIR BAG MODULE
1.
Replace side air bag module LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-120
< DTC/CIRCUIT DIAGNOSIS >
B1135 SIDE AIR BAG MODULE LH
B1135 SIDE AIR BAG MODULE LH
Description
INFOID:0000000009946238
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
INFOID:0000000009946239
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-120, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946240
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1135
SIDE MODULE LH
[VB-SHORT]
Side air bag module LH circuit is shorted to
power supply circuit
• Disconnection of wiring harness and short
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст