Nissan Cube. Manual — part 489
FENDER PROTECTOR
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded View
INFOID:0000000009949378
FENDER PROTECTOR : Removal and Installation
INFOID:0000000009949379
REMOVAL
1.
Remove front tire.
2.
Remove front fender protector fixing screws, bolts and clips.
3.
Disengage fender clips and fender protector, and then remove fender protector.
INSTALLATION
Install in the reverse order of removal.
1.
Fender protector
2.
Fender clip
3.
J nut
4.
Grommet
: Vehicle front
JMKIA3798ZZ
EXT-22
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
FLOOR SIDE FAIRING
Exploded View
INFOID:0000000009949380
Removal and Installation
INFOID:0000000009949381
REMOVAL
FRONT UNDER COVER FRONT
1.
Remove bumper fascia assembly. Refer to
EXT-12, "Removal and Installation"
2.
Remove front under cover front mounting bolts.
3.
Remove front under cover front.
FRONT UNDER COVER
1.
Remove front under cover mounting bolts and clips.
2.
Remove front under cover.
INSTALLATION
Install in the reverse order of removal.
1.
Front under cover front
2.
Front under cover
JMKIA4092ZZ
ROOF SIDE MOLDING
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009949382
Removal and Installation
INFOID:0000000009949383
REMOVAL
1.
Roof side molding
2.
Roof side molding clip
3.
Double-faced adhesive tape
[t: 1.2 mm (0.047 in)]
4.
Paint sealant
5.
Body side outer panel
6.
Stylish glass
7.
Glass molding
8.
Roof panel
: Vehicle front
: Always replace after every disassembly.
JMKIA3799ZZ
EXT-24
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
1.
Disengage roof side molding clip and roof side molding from
rear end, using remover tool (A).
CAUTION:
• Apply protective tape (B) on body to protect the painted
surface from damage.
• Never use an item as a remover tool that could damage
body panel.
2.
Remove roof side molding as shown by the arrow in the figure.
CAUTION:
Never pull the roof side molding strongly.
3.
Pull out and remove the front end of roof side molding (1)
towards vehicle rear after disengaging clip, because the front
end is located under the windshield molding (2).
INSTALLATION
Install from roof side molding rear end to front end in this order after temporarily holding.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
: Clip
: Vehicle front
JMKIA3883ZZ
: Vehicle front
JMKIA3884ZZ
: Clip
JMKIA3885ZZ
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст