Nissan Cube. Manual — part 890
B1081 SEAT BELT PRE-TENSIONER RH
SRC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-78
< DTC/CIRCUIT DIAGNOSIS >
B1082 SEAT BELT PRE-TENSIONER RH
B1082 SEAT BELT PRE-TENSIONER RH
Description
INFOID:0000000009946175
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic
INFOID:0000000009946176
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946177
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SB-6, "SEAT BELT RETRACTOR : Exploded View"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1082
PRE-TEN FRONT RH
[VB-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to power supply circuit
• Disconnection of wiring harness and short
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
B1082 SEAT BELT PRE-TENSIONER RH
SRC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-80
< DTC/CIRCUIT DIAGNOSIS >
B1083 SEAT BELT PRE-TENSIONER RH
B1083 SEAT BELT PRE-TENSIONER RH
Description
INFOID:0000000009946178
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic
INFOID:0000000009946179
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-18, "Diagnosis with Air Bag Warning Lamp"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009946180
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SB-6, "SEAT BELT RETRACTOR : Exploded View"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1083
PRE-TEN FRONT RH
[GND-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to ground
• Disconnection of wiring harness and short
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст