Nissan Cube. Manual — part 59
BCS
COMBINATION SWITCH SYSTEM SYMPTOMS
BCS-85
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009949742
1.
Perform “Data Monitor” of CONSULT to check for any malfunctioning item.
2.
Check the malfunction combinations.
Malfunction item:
×
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Data monitor item
Malfunction
combination
FR WI
PER HI
FR WIP
ER LOW
F
R
W
A
SH
ER
S
W
FR WI
PER INT
RR
WIPE
R
O
N
RR WIP
E
R INT
RR W
ASHER
SW
INT VOL
U
ME
TURN SIG
NAL R
TURN SIGNAL L
T
A
IL
LA
MP
SW
H
I BEAM SW
HEAD LAMP SW
1
HEAD LAMP SW
2
P
ASSI
N
G
SW
AU
T
O
LI
GH
T
S
W
FR F
O
G
SW
×
×
×
×
A
×
×
×
×
B
×
×
×
×
C
×
×
×
×
D
×
×
×
E
×
×
×
F
×
×
×
×
G
×
×
×
H
×
×
×
×
I
×
×
×
×
J
All Items
K
If only one item is detected or the item is not applicable to the combinations A to K
L
Malfunction
combination
Malfunctioning part
Repair or replace
A
Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to
.
B
Combination switch OUTPUT 2 circuit
C
Combination switch OUTPUT 3 circuit
D
Combination switch OUTPUT 4 circuit
E
Combination switch OUTPUT 5 circuit
F
Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to
.
G
Combination switch INPUT 2 circuit
H
Combination switch INPUT 3 circuit
I
Combination switch INPUT 4 circuit
J
Combination switch INPUT 5 circuit
K
BCM
L
Combination switch
Replace combination switch.
BCS-86
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000009949743
SHIPPING MODE
• Shipping mode inhibits battery power consumption during transportation or storage of the vehicle. Vehicle is
set to shipping mode before being shipped from the factory.
• When ignition switch is OFF, BCM operates shipping mode.
• BCM control functions are limited in shipping mode. The limited items that are not operated during the ship-
ping mode are as follows.
- Door lock and unlock switch function
- Remote keyless entry function
- Theft warning alarm function
- Lighting & turn signal switch function
- Interior room lamp timer control function
• For shipping mode cancel operation, refer to
.
NOTE:
Do not cancel shipping mode during storage of the vehicle. Always cancel shipping mode before delivery of
the vehicle to customer.
BCS
PRECAUTIONS
BCS-87
< PRECAUTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010166643
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010166645
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
SEF289H
BCS-88
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Exploded View
INFOID:0000000009949745
NOTE:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specification. Refer
to
.
Removal and Installation
INFOID:0000000009949746
NOTE:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specification. Refer
to
.
REMOVAL
1.
Remove knee protector. Refer to
.
2.
Remove fuse block (J/B).
3.
Remove harness clip.
4.
Remove screws.
5.
Remove BCM and disconnect the connector.
6.
Remove the ignition relay and back door lock actuator relay.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform “WRITE CONFIGURATION” when replacing BCM. Or not doing so, BCM control
function does not operate normally.
NOTE:
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to
.
1.
BCM
JPMIA1516ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст