Nissan Cube. Manual — part 816
B26FC KEY REGISTRATION
SEC-75
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B26FC KEY REGISTRATION
Description
INFOID:0000000009950175
When door request switch or push-button ignition switch is pressed, BCM verifies Intelligent Key that is regis-
tered to the vehicle. If verification result is OK, door lock, door unlock, and engine start are allowed.
DTC Logic
INFOID:0000000009950176
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
2.
Check “Self-diagnosis result” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009950177
1.
REPLACE INTELLIGENT KEY
1.
Replace Intelligent Key that matches the vehicle.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
3.
Check “Self-diagnosis result” using CONSULT.
Is DTC detected?
YES
>> Replace BCM. Refer to
BCS-88, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26FC
KEY REGISTRA-
TION
Intelligent Key that does not match the vehicle is
registered.
• Improper registration operation
• Intelligent Key
• BCM
SEC-76
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210B STARTER CONTROL RELAY
B210B STARTER CONTROL RELAY
Description
INFOID:0000000009950178
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in the N or P position. It
is installed parallel to the starter relay.
DTC Logic
INFOID:0000000009950179
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions and wait 1 second or more.
-
Selector lever is in the P or N position
-
Do not depress brake pedal
2.
Check “Self-diagnosis result” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009950180
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self-diagnosis result” for IPDM E/R using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is DTC detected?
YES
>> Replace IPDM E/R. Refer
PCS-34, "Removal and Installation"
.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210B
START CONT RLY ON
When comparing the following items, a malfunction
is detected for 1 second or more.
• Starter relay ON signal (CAN) from BCM
• Starter control relay conditions of contact side
and coil side
• Transmission range switch input
IPDM E/R
B210C STARTER CONTROL RELAY
SEC-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210C STARTER CONTROL RELAY
Description
INFOID:0000000009950181
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in the N or P position. It
is installed parallel to the starter relay.
DTC Logic
INFOID:0000000009950182
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions and wait 1 second or more.
-
Selector lever is in the P or N position
-
Do not depress brake pedal
2.
Check “Self-diagnosis result” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009950183
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self-diagnosis result” for IPDM E/R using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is DTC detected?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210C
START CONT RLY OFF
When comparing the following items, a malfunction is
detected for 1 second or more.
• Starter relay ON signal (CAN) from BCM
• Starter control relay conditions of contact side and coil
side
• Transmission range switch input
IPDM E/R
SEC-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210D STARTER RELAY
B210D STARTER RELAY
Description
INFOID:0000000009950184
Located in IPDM E/R, the starter relay runs the starter motor. The starter relay is turned ON by the BCM when
the ignition switch is in the START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN
communication.
DTC Logic
INFOID:0000000009950185
DTC DETECTION LOGIC
NOTE:
If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions and wait for 1 second or more.
-
Selector lever is in the P or N position
-
Do not depress brake pedal
2.
Check “Self-diagnosis result” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009950186
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self-diagnosis result” for IPDM E/R using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is DTC detected?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210D
STARTER RELAY ON
When comparing the following items, a malfunction is
detected for 1 second or more.
• Starter relay ON signal (CAN) from BCM
• Starter control relay conditions of contact side and
coil side
• Transmission range switch input
IPDM E/R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст