Nissan Murano Z51 (2013 year). Manual — part 1
ACC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
ACC
A
ACC
N
O
P
CONTENTS
ACCELERATOR CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
FOR USA AND CANADA . . . . . . . . . . ....
FOR MEXICO . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
ACCELERATOR CONTROL SYSTEM . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
Revision: 2012 September
2013 MURANO
ACC-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000008457774
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000008457775
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Revision: 2012 September
2013 MURANO
PRECAUTIONS
ACC-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
ACC
N
P
O
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 September
2013 MURANO
ACC-4
< REMOVAL AND INSTALLATION >
ACCELERATOR CONTROL SYSTEM
REMOVAL AND INSTALLATION
ACCELERATOR CONTROL SYSTEM
Exploded View
INFOID:0000000008457776
Removal and Installation
INFOID:0000000008457777
REMOVAL
1.
Disconnect accelerator pedal position sensor harness connector.
2.
Remove accelerator pedal assembly.
CAUTION:
• Never disengage accelerator pedal assembly and bracket.
• Never disassemble accelerator lever. Never remove accelerator pedal position sensor from
accelerator lever.
• Avoid impact from dropping etc. during handling.
• Be careful to keep accelerator lever away from water.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000008457778
INSPECTION AFTER INSTALLATION
1.
Accelerator pedal assembly
: Vehicle front
: N·m (kg-m, ft-lb)
JPBIA1692GB
Revision: 2012 September
2013 MURANO
ACCELERATOR CONTROL SYSTEM
ACC-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
ACC
N
P
O
• Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and
released.
• Check accelerator pedal securely returns to the fully released position.
• For the electrical inspection of accelerator pedal position sensor, refer to
EC-419, "Component Inspection"
.
-
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “Accelerator
Pedal Released Position Learning”. Refer to
EC-18, "ACCELERATOR PEDAL RELEASED POSITION
Revision: 2012 September
2013 MURANO
BCS
BCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
BCS
A
O
P
N
CONTENTS
BODY CONTROL SYSTEM
BASIC INSPECTION . . . . . . . . .
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) . . . . . . . . . . . ...
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Description . . . . . ...
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Work Procedure . . . ...
CONFIGURATION (BCM) . . . . . . . . . . ...
CONFIGURATION (BCM) : Description . . . . ....
CONFIGURATION (BCM) : Work Procedure . . ....
CONFIGURATION (BCM) : Configuration list . . ...
SHIPPING MODE CANCEL OPERATION . . ..
Description . . . . . . . . . . . . . . . ....
Work Procedure . . . . . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
BODY CONTROL SYSTEM . . . . . . . .
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
COMBINATION SWITCH READING SYSTEM
.
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
SIGNAL BUFFER SYSTEM . . . . . . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
POWER CONSUMPTION CONTROL SYS-
TEM . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
DOOR LOCK . . . . . . . . . . . . . . . ..
DOOR LOCK : CONSULT Function (BCM -
DOOR LOCK) . . . . . . . . . . . . . . ..
REAR WINDOW DEFOGGER . . . . . . . . ...
REAR WINDOW DEFOGGER : CONSULT Func-
tion (BCM - REAR DEFOGGER) . . . . . . . .
BUZZER . . . . . . . . . . . . . . . . . .
BUZZER : CONSULT Function (BCM - BUZZER) .
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) . . . . . . . . . . . . . . . . . ..
WIPER . . . . . . . . . . . . . . . . . .
WIPER : CONSULT Function (BCM - WIPER) . ...
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT Function (BCM - FLASH-
ER) . . . . . . . . . . . . . . . . . . ..
INTELLIGENT KEY . . . . . . . . . . . . .
INTELLIGENT KEY : CONSULT Function (BCM -
INTELLIGENT KEY) . . . . . . . . . . . .
COMB SW . . . . . . . . . . . . . . . . ..
COMB SW : CONSULT Function (BCM - COMB
SW) . . . . . . . . . . . . . . . . . . ..
BCM . . . . . . . . . . . . . . . . . . ...
BCM : CONSULT Function (BCM - BCM) . . . ...
IMMU . . . . . . . . . . . . . . . . . . ..
IMMU : CONSULT Function (BCM - IMMU) . . .
Revision: 2012 September
2013 MURANO
BCS-2
BATTERY SAVER . . . . . . . . . . . . ....
BATTERY SAVER : CONSULT Function (BCM -
BATTERY SAVER) . . . . . . . . . . . . .
TRUNK . . . . . . . . . . . . . . . . . ..
TRUNK : CONSULT Function (BCM - TRUNK) . .
THEFT ALM . . . . . . . . . . . . . . . ..
THEFT ALM : CONSULT Function (BCM -
THEFT) . . . . . . . . . . . . . . . . ...
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
SIGNAL BUFFER . . . . . . . . . . . . . ..
SIGNAL BUFFER : CONSULT Function (BCM -
SIGNAL BUFFER) . . . . . . . . . . . . ..
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
U1000 CAN COMM . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
U1010 CONTROL UNIT (CAN) . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
U0415 VEHICLE SPEED SIG . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2562 LOW VOLTAGE . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
COMBINATION SWITCH INPUT CIRCUIT . ...
Diagnosis Procedure . . . . . . . . . . . ...
COMBINATION SWITCH OUTPUT CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . .
BCM (BODY CONTROL MODULE) . . . . ..
Reference Value . . . . . . . . . . . . . .
Wiring Diagram - BCM - . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . .
COMBINATION SWITCH SYSTEM SYMP-
TOMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
NORMAL OPERATING CONDITION . . . .
Description . . . . . . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . . .
FOR USA AND CANADA . . . . . . . . . . .
FOR MEXICO . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ..
BCM (BODY CONTROL MODULE) . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COMBINATION SWITCH . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2012 September
2013 MURANO
BCS
INSPECTION AND ADJUSTMENT
BCS-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000008458087
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Proce-
dure
INFOID:0000000008458088
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
BCS-84, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to
BCS-4, "CONFIGURATION (BCM) : Work Procedure"
.
>> GO TO 4.
4.
INITIALIZE BCM (NATS) (IF EQUIPPED)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
Revision: 2012 September
2013 MURANO
BCS-4
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
CONFIGURATION (BCM) : Description
INFOID:0000000008458089
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
CONFIGURATION (BCM) : Work Procedure
INFOID:0000000008458090
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT Configuration
1.
Select "WRITE CONFIGURATION - Manual selection".
2.
Identify the correct model and configuration list. Refer to
BCS-5, "CONFIGURATION (BCM) : Configura-
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “SETTING”. Refer to
BCS-5, "CONFIGURATION (BCM) : Configuration
for written items and setting value.
4.
Select "SETTING".
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5.
When "COMMAND FINISHED", select "END".
>> GO TO 4.
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection
Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
Revision: 2012 September
2013 MURANO
BCS
INSPECTION AND ADJUSTMENT
BCS-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
CONFIGURATION (BCM) : Configuration list
INFOID:0000000008458091
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
EXCEPT FOR MEXICO
⇔
: Items which confirm vehicle specifications
MANUAL SETTING ITEM
NOTE
Items
Setting value
AV C/U
WITH
⇔
WITHOUT
• WITH: With navigation system
• WITHOUT: Without navigation system
AUTO BACK DOOR
WITH
⇔
WITHOUT
• WITH: With automatic back door system
• WITHOUT: Without automatic back door system
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITH
⇔
WITHOUT
• WITH: With daytime running light system
• WITHOUT: Without daytime running light system
RAIN SENSOR
WITH
⇔
WITHOUT
—
THEFT ALM AREA
WITHOUT
⇔
MODE2
• WITHOUT: Without vehicle security system
• MODE2: With vehicle security system
Key Fob Type
MODE7
⇔
MODE9
• MODE7: With automatic back door system
• MODE9: Without automatic back door system
AUTO SETTING ITEM
NOTE
Items
Setting value
BATTERY SAVER FUNCTION
MODE3
—
Trunk/Glass Hatch select
Glass Hatch
Even on a vehicle without glass hatch. It displays “Glass
Hatch”.
TRANSIT MODE
WITH
—
ACC BAT SAVE FUNC
MODE2
—
TR OPEN SW (INT)
MODE1
—
H/L BULB
DEFAULT
—
FR FOG LAMP
WITH
—
RR FOG LAMP
WITH
Even on a vehicle without rear fog lamp. It displays “WITH”.
DI LMP VARIAT
MODE2
—
LIGHT RECOG
MODE7
TRANSMISSION
AT with ABS
—
REAR WIPER
WITH
—
HAZARD SW TYPE
MODE1
—
TR CANCEL SW
WITHOUT
—
BCM AC CONTROL
MODE1
—
TRUNK ACT OUTPUT
MODE2
—
TPMS WITH
—
TIRE PRESSURE
230kPa
—
Revision: 2012 September
2013 MURANO
BCS-6
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
FOR MEXICO
⇔
: Items which confirm vehicle specifications
RAIN SEN TYPE
MODE2
—
FOG ON WITH AUTO LIGHT
WITHOUT
—
AUTO SETTING ITEM
NOTE
Items
Setting value
MANUAL SETTING ITEM
NOTE
Items
Setting value
AV C/U
WITH
—
AUTO BACK DOOR
WITHOUT
—
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITHOUT
—
RAIN SENSOR
WITH
⇔
WITHOUT
—
THEFT ALM AREA
MODE2
—
HAZARD SW TYPE
MODE1
—
AUTO SETTING ITEM
NOTE
Items
Setting value
BATTERY SAVER FUNCTION
MODE3
—
Trunk/Glass Hatch select
Glass Hatch
Even on a vehicle without glass hatch. It displays “Glass
Hatch”.
TRANSIT MODE
WITH
—
ACC BAT SAVE FUNC
MODE2
—
TR OPEN SW (INT)
MODE1
—
H/L BULB
DEFAULT
—
FR FOG LAMP
WITH
—
RR FOG LAMP
WITH
Even on a vehicle without rear fog lamp. It displays “WITH”.
DI LMP VARIAT
MODE2
—
LIGHT RECOG
MODE7
TRANSMISSION
AT with ABS
—
REAR WIPER
WITH
—
TR CANCEL SW
WITHOUT
—
BCM AC CONTROL
MODE1
—
TRUNK ACT OUTPUT
MODE2
—
TPMS WITHOUT
—
TIRE PRESSURE
240kPa
—
RAIN SEN TYPE
MODE2
—
FOG ON WITH AUTO LIGHT
WITHOUT
—
Key Fob Type
MODE9
—
Revision: 2012 September
2013 MURANO
BCS
SHIPPING MODE CANCEL OPERATION
BCS-7
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SHIPPING MODE CANCEL OPERATION
Description
INFOID:0000000008942327
SYSTEM DIAGRAM
DESCRIPTION
• The combination meter transmits meter CAN signal*
1
to BCM via CAN communication, when the extended
storage fuse switch is ON.
• BCM switches the status (shipping mode or normal mode) by itself according to the meter CAN signal*
1
from
combination meter, and transmits shipping mode status signal to combination meter via CAN communica-
tion.
• The combination meter displays extended storage fuse warning message*
2
on the information display, and
turns the turn signal indicator lamp (LH/RH) ON, when BCM is in shipping mode.
• BCM control functions are limited in shipping mode. Refer to
*1: Odometer signal, wake up signal and each signal.
*2: When shipping mode function operates, “SHIPPING MODE ON PUSH STORAGE FUSE” is displayed.
Work Procedure
INFOID:0000000008942328
1.
SHIPPING MODE CANCEL OPERATION
1.
Turn ignition switch OFF.
2.
Push in (switch on) the extended storage fuse switch. Refer to
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.
SHIPPING MODE CANCEL CHECK
1.
Turn ignition switch ON.
2.
Check that extended storage fuse warning message is not displays on information display.
>> WORK END
JMMIA1345GB
Revision: 2012 September
2013 MURANO
BCS-8
< SYSTEM DESCRIPTION >
BODY CONTROL SYSTEM
SYSTEM DESCRIPTION
BODY CONTROL SYSTEM
System Description
INFOID:0000000008458094
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT and various set-
tings.
BCM CONTROL FUNCTION LIST
System
Reference
Combination switch reading system
Signal buffer system
Power consumption control system
Auto light system
Turn signal and hazard warning lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Headlamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Parking, license plate and tail lamps system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Front fog lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Exterior lamp battery saver system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Daytime running light system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Interior room lamp control system
Step lamp system
Interior room lamp battery saver system
Front wiper and washer system
•
WW-6, "WITH RAIN SENSOR : System Diagram"
(With rain
sensor)
•
WW-10, "WITHOUT RAIN SENSOR : System Diagram"
out rain sensor)
Rear wiper and washer system
Warning chime system
WCS-5, "WARNING CHIME SYSTEM : System Diagram"
Door lock system
Automatic back door system
Automatic drive positioner system
ADP-12, "AUTOMATIC DRIVE POSITIONER SYSTEM : System
Diagram"
Nissan Vehicle Immobilizer System (NVIS) - NATS
Vehicle security system
Panic alarm
Revision: 2012 September
2013 MURANO
BCS
BODY CONTROL SYSTEM
BCS-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Component Parts Location
INFOID:0000000008458095
Rear window defogger system
•
DEF-4, "WITH BOSE SYSTEM : System Diagram"
(With
BOSE system)
•
DEF-6, "WITHOUT BOSE SYSTEM : System Diagram"
(With-
out BOSE system)
Intelligent Key system/engine start system
DLK-18, "INTELLIGENT KEY SYSTEM : System Diagram"
Power window system
Retained accessory power (RAP) system
Tire pressure monitor system (TPMS) - AIR PRESSURE MONI-
TOR
System
Reference
1.
BCM
A.
Behind of combination meter
JPMIA0897ZZ
Revision: 2012 September
2013 MURANO
BCS-10
< SYSTEM DESCRIPTION >
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING SYSTEM
System Diagram
INFOID:0000000008458096
NOTE:
• *1: TAIL LAMP switch links lighting switch 1ST position.
• *2: “FR WIP INT/AT” is FR WIPER INT/AUTO.
System Description
INFOID:0000000008458097
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
Combination switch circuit
NOTE:
• *1: TAIL LAMP switch links lighting switch 1ST position.
• *2: “FR WIP INT/AT” is FR WIPER INT/AUTO.
JMMIA0292GB
JMMIA0293GB
Revision: 2012 September
2013 MURANO
BCS
COMBINATION SWITCH READING SYSTEM
BCS-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Combination switch INPUT-OUTPUT system list
NOTE:
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION
Description
• BCM reads the status of the combination switch at 10 ms interval normally.
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption mode.
• BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5
→
4
→
3
→
2
→
1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
System
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
OUTPUT 5
INPUT 1
—
FR WASHER
FR WIPER LOW
TURN LH
TURN RH
INPUT 2
FR WIPER HI
—
FR WIPER INT/
AUTO
PASSING
HEADLAMP 1
INPUT 3
WIP VOLUME 1
RR WASHER
—
HEADLAMP 2
HI BEAM
INPUT 4
RR WIPER INT
WIP VOLUME 3
AUTO LIGHT
—
TAIL LAMP
INPUT 5
WIP VOLUME 2
RR WIPER ON
—
FR FOG
—
JPMIA0067GB
JPMIA0068GB
Revision: 2012 September
2013 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст