Nissan Murano Z51 (2013 year). Manual — part 65
PWO
POWER SOCKET
PWO-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SOCKET
FRONT POWER SOCKET
FRONT POWER SOCKET : Exploded View
INFOID:0000000008459803
FRONT POWER SOCKET : Removal and Installation
INFOID:0000000008459804
REMOVAL
1.
Remove front console pocket. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from front console pocket while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and front console pocket.
CONSOLE POWER SOCKET
CONSOLE POWER SOCKET : Exploded View
INFOID:0000000008459805
CONSOLE POWER SOCKET : Removal and Installation
INFOID:0000000008459806
REMOVAL
1.
Remove console finisher assembly. Refer to
.
1
: Inner socket
2
: Ring
JPMIA0782ZZ
D
: Cut out
JPMIA0783ZZ
1
: Inner socket
2
: Ring
JSMIA0522ZZ
Revision: 2012 September
2013 MURANO
PWO-8
< REMOVAL AND INSTALLATION >
POWER SOCKET
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (D).
4.
Remove ring (2) from console box while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console box.
LUGGAGE ROOM POWER SOCKET
LUGGAGE ROOM POWER SOCKET : Exploded View
INFOID:0000000008459807
LUGGAGE ROOM POWER SOCKET : Removal and Installation
INFOID:0000000008459808
REMOVAL
1.
Remove luggage side finisher lower (RH). Refer to
2.
Disconnect power socket connector (A).
3.
Remove retainer (1) and remove power socket assembly.
4.
Pull out inner socket (2) by pushing the ring pawl (D) from the
inner socket hole (square) (C).
5.
Remove ring (3) from luggage side finisher lower (RH) while
pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and luggage side finisher lower (RH).
B
: Hole for power socket
(Console box)
E
: Cut out
JSMIA0233ZZ
1
: Inner socket
2
: Ring
3
: Retainer
JPMIA1299ZZ
B
: Cut out
JPMIA1300ZZ
Revision: 2012 September
2013 MURANO
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
2WD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR WHEEL HUB AND HOUSING . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR WHEEL HUB AND HOUSING . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ...
Wheel Bearing . . . . . . . . . . . . . . ...
AWD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ..
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . .
REAR WHEEL HUB AND HOUSING . . . ...
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
REAR WHEEL HUB AND HOUSING . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
FINAL DRIVE SIDE . . . . . . . . . . . . .
FINAL DRIVE SIDE : Disassembly and Assembly .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2012 September
2013 MURANO
RAX-2
< SYMPTOM DIAGNOSIS >
[2WD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000008458302
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
NVH in RAX and RSU sections
NVH in WT
section
NVH in WT
section
NVH in BR
section
Possible cause and SUSPECTED PARTS
Im
pro
per in
st
a
lla
ti
on
,
lo
os
en
es
s
Part
s int
e
rference
Whe
e
l be
ari
n
g
da
m
age
REAR AXLE AND RE
AR SUSPENSI
ON
TIRE
ROA
D
WHEEL
BRAKE
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2012 September
2013 MURANO
PREPARATION
RAX-3
< PREPARATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000008458303
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 September
2013 MURANO
RAX-4
< PERIODIC MAINTENANCE >
[2WD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000008458304
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
Revision: 2012 September
2013 MURANO
REAR WHEEL HUB AND HOUSING
RAX-5
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000008458305
Removal and Installation
INFOID:0000000008458306
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-122, "REAR WHEEL SENSOR : Exploded
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. Refer to
BR-48, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
6.
Remove wheel hub and bearing assembly.
7.
Remove parking brake shoe and parking brake cable from back plate. Refer to
8.
Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
9.
Remove stabilizer connecting rod (upper side) with power tool. Refer to
.
10. Remove radius rod (axle housing side). Refer to
11. Remove coil spring. Refer to
12. Set suitable jack under axle housing.
13. Remove front lower link (shock absorber side) with power tool. Refer to
14. Remove front lower link (axle housing side). Refer to
.
15. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
1.
Ball seat
2.
Bushing
3.
Cotter pin
4.
Axle housing
5.
Hub cap
6.
Back plate
7.
Anchor block
8.
Wheel hub and bearing assembly
Refer to
JSDIA2891GB
Revision: 2012 September
2013 MURANO
RAX-6
< REMOVAL AND INSTALLATION >
[2WD]
REAR WHEEL HUB AND HOUSING
CAUTION:
Temporarily tighten nuts to prevent damage to threads and to prevent the ball joint remover from
coming off.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and steering knuckle.
• Never reuse cotter pin.
Inspection
INFOID:0000000008458307
INSPECTION AFTER REMOVAL
Wheel Hub and Bearing Assembly
Check the wheel hub and bearing assembly for wear, cracks, and damage. Replace if necessary.
Axle Housing
Check the axle housing for wear, cracks, and damage. Replace if necessary.
Ball Joint Inspection
Check for boot breakage, axial looseness, and torque of suspension arm ball joint. Refer to
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke). Refer to
PB-3, "Inspection and Adjustment"
.
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Revision: 2012 September
2013 MURANO
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-7
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000008458308
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Revision: 2012 September
2013 MURANO
RAX-8
< SYMPTOM DIAGNOSIS >
[AWD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000008458309
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in DLN section
NVH in DLN section
NVH in RAX
and RSU
sections
Refer to REAR AXLE i
n
t
h
is chart
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
oi
nt
an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Imb
al
anc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
loo
s
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2012 September
2013 MURANO
PRECAUTIONS
RAX-9
< PRECAUTION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000008458310
• Observe the following precautions when disassembling and assembling drive shaft.
• Never disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper waste. Do not use fabric shop cloths because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2012 September
2013 MURANO
RAX-10
< PREPARATION >
[AWD]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000008458311
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 September
2013 MURANO
REAR WHEEL HUB AND HOUSING
RAX-11
< PERIODIC MAINTENANCE >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000008458312
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
Revision: 2012 September
2013 MURANO
RAX-12
< PERIODIC MAINTENANCE >
[AWD]
REAR DRIVE SHAFT
REAR DRIVE SHAFT
Inspection
INFOID:0000000008458313
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
Revision: 2012 September
2013 MURANO
REAR WHEEL HUB AND HOUSING
RAX-13
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000008458314
Removal and Installation
INFOID:0000000008458315
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-122, "REAR WHEEL SENSOR : Exploded
.
3.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Exploded View"
.
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. Refer to
BR-48, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft. Remove the wheel hub lock nut.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for housing (or joint sub-assembly), shaft
and the other parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub and bearing assembly.
9.
Remove parking brake shoe and parking brake cable from back plate. Refer to
1.
Ball seat
2.
Bushing
3.
Cotter pin
4.
Axle housing
5.
Hub cap
6.
Back plate
7.
Anchor block
8.
Wheel hub and bearing assembly
9.
Wheel hub lock nut
Refer to
JSDIA3328GB
Revision: 2012 September
2013 MURANO
RAX-14
< REMOVAL AND INSTALLATION >
[AWD]
REAR WHEEL HUB AND HOUSING
10. Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
11. Remove stabilizer connecting rod (upper side) with power tool. Refer to
.
12. Remove radius rod (axle housing side). Refer to
13. Remove coil spring. Refer to
14. Set suitable jack under axle housing.
15. Remove front lower link (shock absorber side) with power tool. Refer to
16. Remove front lower link (axle housing side). Refer to
.
17. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
CAUTION:
• Temporarily tighten nuts to prevent damage to threads and to prevent the ball joint remover from
coming off.
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for counterpart such as joint sub-assem-
bly, and other parts.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and axle housing.
• Never reuse cotter pin.
Inspection
INFOID:0000000008458316
INSPECTION AFTER REMOVAL
Wheel Hub and Bearing Assembly
Check the wheel hub and bearing assembly for wear, cracks, and damage. Replace if necessary.
Axle Housing
Check the axle housing for wear, cracks, and damage. Replace if necessary.
Ball Joint Inspection
Check for boot breakage, axial looseness, and torque of suspension arm ball joint. Refer to
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke). Refer to
PB-3, "Inspection and Adjustment"
.
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Revision: 2012 September
2013 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст