Nissan Murano Z51 (2013 year). Manual — part 94
WCS
BCM (BODY CONTROL MODULE)
WCS-67
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal.
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO
operation, BCM operates a fail-safe control.
NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF
⇒
ON and front wiper switch is INT/
AUTO position, BCM operates a fail-safe control.
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1.
More than 1 minute is passed after the rear wiper stop.
2.
Turn rear wiper switch OFF.
3.
Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart
INFOID:0000000008946115
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Display contents of CONSULT
Fail-safe
Cancellation
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→
OFF
B2560: STARTER CONT RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
• Starter control relay signal
• Starter relay status signal
B2608: STARTER RELAY
Inhibit engine cranking
500 ms after the following signal communication status becomes
consistent
• Starter motor relay control signal
• Starter relay status signal (CAN)
B260A: IGNITION RELAY
Inhibit engine cranking
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B260F: ENG STATE SIG LOST
Maintains the power supply
position attained at the time
of DTC detection
When any of the following conditions are fulfilled
• Power position changes to ACC
• Receives engine status signal (CAN)
B2617: STARTER RELAY CIRC
Inhibit engine cranking
1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM
Inhibit engine cranking
1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B261E: VEHICLE TYPE
Inhibit engine cranking
BCM initialization
Revision: 2012 September
2013 MURANO
WCS-68
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000008946116
NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to
MON ITEM : CONSULT Function (BCM - COMMON ITEM)"
Priority
DTC
1
B2562: LOW VOLTAGE
2
• U1000: CAN COMM
• U1010: CONTROL UNIT(CAN)
3
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
4
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2608: STARTER RELAY
• B260A: IGNITION RELAY
• B260F: ENG STATE SIG LOST
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
5
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1734: CONTROL UNIT
6
• B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA
Revision: 2012 September
2013 MURANO
WCS
BCM (BODY CONTROL MODULE)
WCS-69
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CONSULT display
Fail-safe
Freeze Frame
Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condi-
tion
Intelligent Key
warning lamp ON
Tire pressure
monitor warning
lamp ON
Reference
No DTC is detected.
further testing
may be required.
—
—
—
—
—
U1000: CAN COMM
—
—
—
—
U1010: CONTROL UNIT(CAN)
—
—
—
—
U0415: VEHICLE SPEED SIG
—
—
—
—
B2190: NATS ANTENNA AMP
×
—
—
—
B2191: DIFFERENCE OF KEY
×
—
—
—
B2192: ID DISCORD BCM-ECM
×
—
—
—
B2193: CHAIN OF BCM-ECM
×
—
—
—
B2195: ANTI SCANNING
×
—
—
—
B2553: IGNITION RELAY
—
×
—
—
B2555: STOP LAMP
—
×
—
—
B2556: PUSH-BTN IGN SW
—
×
×
—
B2557: VEHICLE SPEED
×
×
×
—
B2560: STARTER CONT RELAY
×
×
×
—
B2562: LOW VOLTAGE
—
×
—
—
B2601: SHIFT POSITION
×
×
×
—
B2602: SHIFT POSITION
×
×
×
—
B2603: SHIFT POSI STATUS
×
×
×
—
B2604: PNP SW
×
×
×
—
B2605: PNP SW
×
×
×
—
B2608: STARTER RELAY
×
×
×
—
B260A: IGNITION RELAY
×
×
×
—
B260F: ENG STATE SIG LOST
×
×
×
—
B2614: ACC RELAY CIRC
—
×
×
—
B2615: BLOWER RELAY CIRC
—
×
×
—
B2616: IGN RELAY CIRC
—
×
×
—
B2617: STARTER RELAY CIRC
×
×
×
—
B2618: BCM
×
×
×
—
B261A: PUSH-BTN IGN SW
—
×
×
—
B261E: VEHICLE TYPE
×
×
×
(Turn ON for 15
seconds)
—
B2622: INSIDE ANTENNA
—
×
—
—
B2623: INSIDE ANTENNA
—
×
—
—
B26EA: KEY REGISTRATION
—
×
×
(Turn ON for 15
seconds)
—
C1704: LOW PRESSURE FL
—
—
—
×
C1705: LOW PRESSURE FR
—
—
—
×
C1706: LOW PRESSURE RR
—
—
—
×
C1707: LOW PRESSURE RL
—
—
—
×
Revision: 2012 September
2013 MURANO
WCS-70
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
C1708: [NO DATA] FL
—
—
—
×
C1709: [NO DATA] FR
—
—
—
×
C1710: [NO DATA] RR
—
—
—
×
C1711: [NO DATA] RL
—
—
—
×
C1716: [PRESSDATA ERR] FL
—
—
—
×
C1717: [PRESSDATA ERR] FR
—
—
—
×
C1718: [PRESSDATA ERR] RR
—
—
—
×
C1719: [PRESSDATA ERR] RL
—
—
—
×
C1729: VHCL SPEED SIG ERR
—
—
—
×
C1734: CONTROL UNIT
—
—
—
×
CONSULT display
Fail-safe
Freeze Frame
Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condi-
tion
Intelligent Key
warning lamp ON
Tire pressure
monitor warning
lamp ON
Reference
Revision: 2012 September
2013 MURANO
WCS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
WCS-71
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000008459191
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000008459192
1.
CHECK PARKING BRAKE WARNING LAMP
1.
Start the engine.
2.
Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace the combination meter.
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform a check for the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
MWI-54, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace the combination meter.
NO
>> Replace the parking brake switch. Refer to
When parking brake is applied
: ON
When parking brake is released
: OFF
Revision: 2012 September
2013 MURANO
WCS-72
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000008459193
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000008459194
1.
CHECK COMBINATION SWITCH (LIGHT SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (light switch).
Do they operate normally?
YES
>> GO TO 2.
NO
>> Refer to
(xenon type) or
(halogen type).
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL CIRCUIT
Perform the check for the front door switch (driver side) signal circuit. Refer to
BACK DOOR : Diagnosis Procedure"
DLK-99, "WITHOUT AUTOMATIC BACK
(without automatic back door).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Perform a unit check for the front door switch (driver side). Refer to
DLK-101, "WITHOUT AUTOMATIC BACK
(without automatic back door).
Is the inspection result normal?
YES
BCS-84, "Removal and Installation"
NO
>> Replace the front door switch (driver side). Refer to
DLK-313, "Removal and Installation"
.
Revision: 2012 September
2013 MURANO
WCS
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
WCS-73
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000008459195
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
INFOID:0000000008459196
1.
CHECK SEAT BELT WARNING LAMP
1.
Turn ignition switch ON.
2.
Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK BCM OUTPUT SIGNAL
Check if the light reminder warning chime is activated by performing BCM active test. Refer to
"BUZZER : CONSULT Function (BCM - BUZZER)"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to
"CONSULT Function (METER/M&A)"
Is the inspection result normal?
YES
>> Replace the combination meter.
NO
>> Replace the BCM. Refer to
BCS-84, "Removal and Installation"
4.
CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
Perform the check for the seat belt buckle switch circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to
WCS-26, "Component Inspection"
Is the inspection result normal?
YES
>> Replace the combination meter.
NO
>> Replace the seat belt buckle. Refer to
SB-9, "SEAT BELT BUCKLE : Removal and Installation"
.
Seat belt fastened
: OFF
Seat belt not fastened
: ON
Buzzer active condition
: On
Buzzer non-active condition
: Off
Revision: 2012 September
2013 MURANO
WCS-74
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND
THE KEY WARNING DOES NOT SOUND
Description
INFOID:0000000008459197
The is key warning chime does not sound under the following conditions.
• Key inserted into the key slot. (Key slot switch ON)
• Ignition switch is not in ON or START. (Ignition switch signal OFF)
• Front door switch (driver side) is open. [Door switch signal (driver side) ON]
Diagnosis Procedure
INFOID:0000000008459198
1.
CHECK BCM INPUT SIGNAL
1.
Connect CONSULT.
2.
Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY SW-SLOT” monitor value. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-84, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK KEY SLOT SWITCH SIGNAL CIRCUIT
Check the key slot switch signal circuit. Refer to
DLK-129, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check applicable parts, and repair or replace corresponding parts.
3.
CHECK DOOR SWITCH SIGNAL (DRIVER SIDE) CIRCUIT
Check the door switch signal (driver side) circuit. Refer to
DLK-97, "WITH AUTOMATIC BACK DOOR : Diag-
(with automatic back door) or
DLK-99, "WITHOUT AUTOMATIC BACK DOOR : Diagnosis
(without automatic back door).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check the front door switch (driver side). Refer to
DLK-98, "WITH AUTOMATIC BACK DOOR : Component
(with automatic back door) or
DLK-101, "WITHOUT AUTOMATIC BACK DOOR : Component
(without automatic back door).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-84, "Removal and Installation"
NO
>> Replace front door switch (driver side). Refer to
DLK-313, "Removal and Installation"
.
Revision: 2012 September
2013 MURANO
WCS
PRECAUTIONS
WCS-75
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000008459199
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000008459200
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Revision: 2012 September
2013 MURANO
WCS-76
< PRECAUTION >
PRECAUTIONS
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 September
2013 MURANO
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Notice and Precautions for TPMS . . . ....
Service Notice and Precautions for Road Wheel ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
BCM . . . . . . . . . . . . . . . . . . ..
Tire Pressure Sensor . . . . . . . . . . . ....
Tire Pressure Receiver . . . . . . . . . . .....
Information Display . . . . . . . . . . . . ...
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
AIR PRESSURE MONITOR . . . . . . . . . ....
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ....
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
TIRE PRESSURE MONITORING SYSTEM . ..
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
BCM . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR WAKE UP OP-
ERATION . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR ID REGISTRA-
TION . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
C1704, C1705, C1706, C1707 LOW TIRE
PRESSURE . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Revision: 2012 September
2013 MURANO
WT-2
C1729 VEHICLE SPEED SIGNAL . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1734 BCM . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
TIRE PRESSURE RECEIVER . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
TPMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
BLINKS . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
ID REGISTRATION CANNOT BE COMPLET-
ED . . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ...
ROAD WHEEL . . . . . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ..
ROAD WHEEL TIRE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
TIRE PRESSURE SENSOR . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TIRE PRESSURE RECEIVER . . . . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Road Wheel . . . . . . . . . . . . . . .
Tire Air Pressure . . . . . . . . . . . . . .
Revision: 2012 September
2013 MURANO
PRECAUTIONS
WT-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008454479
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Notice and Precautions for TPMS
INFOID:0000000008454480
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Delete the memory with CONSULT, or register the ID to turn low tire pressure warning lamp
OFF. Refer to
WT-9, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer to
• Replace grommet seal, valve core and cap of tire pressure sensor in TPMS every tire replacement by reach-
ing wear limit of tire. Refer to
Service Notice and Precautions for Road Wheel
INFOID:0000000008454481
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
Revision: 2012 September
2013 MURANO
WT-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000008454482
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000008454483
Tool number
(Kent-Moore No.)
Tool name
Description
–
(J-45295)
Tire pressure sensor activation tool
Tire pressure sensor wake-up procedure and
ID registration.
SEIA0462E
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 September
2013 MURANO
COMPONENT PARTS
WT-5
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000008454484
Component Description
INFOID:0000000008454485
BCM
INFOID:0000000008454486
The BCM reads the air pressure signal received by the tire pressure receiver, and controls the low tire pres-
sure warning lamp operation. It also has a judgment function to detect a system malfunction.
1.
Tire pressure sensor
2.
BCM
3.
Tire pressure receiver
A.
Wheel
B.
Behind of combination meter
C.
Instrument lower panel LH
D.
Low tire pressure warning lamp, infor-
mation display (in combination meter)
JSEIA0308ZZ
Component parts
Function
BCM (Body Control Module)
Tire pressure sensor
Tire pressure receiver
WT-6, "Tire Pressure Receiver"
Turn signal lamp
ID registration of each wheel has been completed, turn signal lamp flashes.
Combination meter
Transmits the vehicle speed signal via CAN communication to BCM.
Receives the following signals via CAN communication to BCM.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal
Low tire pressure warning lamp
Information display
Revision: 2012 September
2013 MURANO
WT-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Tire Pressure Sensor
INFOID:0000000008454487
The tire pressure sensor integrated with a valve is installed on a wheel, and transmits a detected air pressure
signal by radio wave.
Tire Pressure Receiver
INFOID:0000000008454488
The tire pressure receiver receives the air pressure signal transmitted by the tire pressure sensor in each
wheel.
Information Display
INFOID:0000000008454489
The vehicle information display is shown when a low tire pressure warning lamp signal is transmitted from
BCM to combination meter via CAN communication.
Condition
Vehicle information display
Ignition switch OFF
Not indication
Ignition switch ON
Low tire pressure warning lamp remains ON after blinking
for one minute. [Tire Pressure Monitoring System (TPMS)
malfunction.]
Not indication
Ignition switch ON
Low tire pressure warning lamp remains ON. (low tire
pressure)
Indication
Revision: 2012 September
2013 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст