Nissan Murano Z51 (2013 year). Manual — part 41
MA-38
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
DISC BRAKE : Rear Disc Brake
INFOID:0000000008457513
Unit: mm (in)
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000008457514
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
POWER STEERING FLUID AND LINES
POWER STEERING FLUID AND LINES : Inspection
INFOID:0000000008457515
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
• Do not overfill.
• Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
MA-16, "FOR NORTH AMERICA : Fluids and Lubri-
(FOR MEXICO).
• Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
• Check rack boots for accumulation of power steering fluid.
AXLE AND SUSPENSION PARTS
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.050 (0.0020) or less
SLIA0014E
SST850C
SST851C
Revision: 2012 September
2013 MURANO
CHASSIS MAINTENANCE
MA-39
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000008457516
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
DRIVE SHAFT : Inspection
INFOID:0000000008457517
• Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SMA525A
JPPIA0011ZZ
SFA108A
Revision: 2012 September
2013 MURANO
MA-40
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000008457518
For hood and hood lock illustration.
DLK-263, "HOOD ASSEMBLY : Exploded View"
• Hood lock control: Refer to
For door and door lock illustration.
DLK-273, "DOOR ASSEMBLY : Exploded View"
• Front door lock: Refer to
DLK-295, "DOOR LOCK : Exploded View"
.
• Rear door: Refer to
DLK-278, "DOOR ASSEMBLY : Exploded View"
.
• Rear door lock: Refer to
DLK-301, "DOOR LOCK : Exploded View"
For back door and back door lock illustration.
• Back door: Refer to
DLK-283, "BACK DOOR ASSEMBLY : Exploded View"
.
• Back door lock: Refer to
DLK-306, "DOOR LOCK : Exploded View"
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000008457519
For front seat belt illustration. Refer to
SB-7, "SEAT BELT RETRACTOR : Exploded View"
For rear seat belt illustration. Refer to
SB-12, "SEAT BELT RETRACTOR : Exploded View"
.
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-5, "SEAT BELT RETRACTOR : Inspection"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
Revision: 2012 September
2013 MURANO
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-41
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT
DRIVE BELT : Drive Belt
INFOID:0000000008457520
DRIVE BELT
ENGINE COOLANT
ENGINE COOLANT : Periodical Maintenance Specification
INFOID:0000000008457521
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
ENGINE OIL
ENGINE OIL : Periodical Maintenance Specification
INFOID:0000000008457522
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
SPARK PLUG
SPARK PLUG : Spark Plug
INFOID:0000000008457523
SPARK PLUG
Unit: mm (in)
ROAD WHEEL
ROAD WHEEL : Road Wheel
INFOID:0000000008457524
ALUMINUM WHEEL (CONVENTIONAL)
STEEL WHEEL (FOR EMERGENCY USE)
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity (With reservoir tank at “MAX” level)
9.4 (9-7/8, 8-1/4)
Reservoir tank
0.8 (7/8, 3/4)
Drain and refill
With oil filter change
4.6 (4-7/8, 4)
Without oil filter change
4.3 (4-1/2, 3-3/4)
Dry engine (Overhaul)
5.3 (5-5/8, 4-5/8)
Make
DENSO
Standard type
FXE22HR11
Gap
Standard
1.1 (0.043)
Limit
1.4 (0.055)
Item
Limit
Runout
Axial runout
Less than 0.3 mm (0.012 in)
Radial runout
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Revision: 2012 September
2013 MURANO
MA-42
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Item
Limit
Runout
Axial runout (Average)
Less than 1.5 mm (0.059 in)
Radial runout (Average)
Revision: 2012 September
2013 MURANO
MIR-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
MIR
A
B
MIR
N
O
P
CONTENTS
MIRRORS
WITH ADP
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORK FLOW . . .
Work Flow . . . . . . . . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
DOOR MIRROR SYSTEM . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
INSIDE MIRROR SYSTEM . . . . . . . . ..
System Description . . . . . . . . . . . . ...
Component Description . . . . . . . . . . .....
DIAGNOSIS SYSTEM (DRIVER SEAT CON-
TROL UNIT) . . . . . . . . . . . . . . .
Diagnosis Description . . . . . . . . . . . ...
CONSULT Function . . . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . ..
MIRROR SWITCH . . . . . . . . . . . . . .
MIRROR SWITCH : Description . . . . . . . .
MIRROR SWITCH : Component Function Check
MIRROR SWITCH : Diagnosis Procedure . . . ..
MIRROR SWITCH : Component Inspection . . ...
CHANGEOVER SWITCH . . . . . . . . . . ..
CHANGEOVER SWITCH : Description . . . . ..
CHANGEOVER SWITCH : Component Function
Check . . . . . . . . . . . . . . . . . ..
CHANGEOVER SWITCH : Diagnosis Procedure .
CHANGEOVER SWITCH : Component Inspec-
tion . . . . . . . . . . . . . . . . . . ..
DOOR MIRROR . . . . . . . . . . . .
Wiring Diagram - DOOR MIRROR SYSTEM
(WITH AUTOMATIC DRIVE POSITIONER) - . . .
AUTO ANTI-DAZZLING INSIDE MIRROR
SYSTEM . . . . . . . . . . . . . . .
Wiring Diagram - INSIDE MIRROR SYSTEM - . ...
ECU DIAGNOSIS INFORMATION . . . ..
DRIVER SEAT CONTROL UNIT . . . . . ..
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - AUTOMATIC DRIVE POSI-
TIONER CONTROL SYSTEM - . . . . . . . ..
Fail Safe . . . . . . . . . . . . . . . . ..
DTC Index . . . . . . . . . . . . . . . ...
AUTOMATIC DRIVE POSITIONER CON-
TROL UNIT . . . . . . . . . . . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - AUTOMATIC DRIVE POSI-
TIONER CONTROL SYSTEM - . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ..
DOOR MIRROR DOES NOT OPERATE . . ..
Diagnosis Procedure . . . . . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ..
Work Flow . . . . . . . . . . . . . . . .
Inspection Procedure . . . . . . . . . . . ...
Diagnostic Worksheet . . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
FOR USA AND CANADA . . . . . . . . . . ..
Revision: 2012 September
2013 MURANO
MIR-2
FOR USA AND CANADA : Precaution for Proce-
dure without Cowl Top Cover . . . . . . . . .
FOR USA AND CANADA : Precaution for Work ....
FOR MEXICO . . . . . . . . . . . . . . ....
FOR MEXICO : Precaution for Procedure without
Cowl Top Cover . . . . . . . . . . . . . ..
FOR MEXICO : Precaution for Work . . . . . ..
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tools . . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
INSIDE MIRROR . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
OUTSIDE MIRROR . . . . . . . . . . .
DOOR MIRROR ASSEMBLY . . . . . . . . ...
DOOR MIRROR ASSEMBLY : Exploded View . ..
DOOR MIRROR ASSEMBLY : Removal and In-
stallation . . . . . . . . . . . . . . . . .
GLASS MIRROR . . . . . . . . . . . . . ...
GLASS MIRROR : Exploded View . . . . . . .
GLASS MIRROR : Disassembly and Assembly . .
DOOR MIRROR COVER . . . . . . . . . . ...
DOOR MIRROR COVER : Exploded View . . . .
DOOR MIRROR COVER : Disassembly and As-
sembly . . . . . . . . . . . . . . . . ....
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
WITHOUT ADP
SYSTEM DESCRIPTION . . . . . . .
DOOR MIRROR SYSTEM . . . . . . . . .
Component Description . . . . . . . . . . ..
INSIDE MIRROR SYSTEM . . . . . . . .
System Description . . . . . . . . . . . . .
Component Description . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
DOOR MIRROR . . . . . . . . . . . . .
Wiring Diagram - DOOR MIRROR SYSTEM
(WITHOUT AUTOMATIC DRIVE POSITIONER) - ...
AUTO ANTI-DAZZLING INSIDE MIRROR
SYSTEM . . . . . . . . . . . . . . .
Wiring Diagram - INSIDE MIRROR SYSTEM - . ..
SYMPTOM DIAGNOSIS . . . . . . .
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ...
Work Flow . . . . . . . . . . . . . . . ...
Inspection Procedure . . . . . . . . . . . ..
Diagnostic Worksheet . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . . .
FOR USA AND CANADA . . . . . . . . . . .
FOR USA AND CANADA : Precaution for Proce-
dure without Cowl Top Cover . . . . . . . . ..
FOR USA AND CANADA : Precaution for Work . .
FOR MEXICO . . . . . . . . . . . . . . .
FOR MEXICO : Precaution for Procedure without
Cowl Top Cover . . . . . . . . . . . . . ..
FOR MEXICO : Precaution for Work . . . . . ..
PREPARATION . . . . . . . . . . ..
PREPARATION . . . . . . . . . . . . .
Special Service Tools . . . . . . . . . . . .
Commercial Service Tools . . . . . . . . .
REMOVAL AND INSTALLATION . . . ..
INSIDE MIRROR . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
OUTSIDE MIRROR . . . . . . . . . . .
DOOR MIRROR ASSEMBLY . . . . . . . . .
DOOR MIRROR ASSEMBLY : Exploded View . ..
DOOR MIRROR ASSEMBLY : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
GLASS MIRROR . . . . . . . . . . . . . ...
GLASS MIRROR : Exploded View . . . . . . ..
GLASS MIRROR : Disassembly and Assembly . .
DOOR MIRROR COVER . . . . . . . . . . ...
DOOR MIRROR COVER : Exploded View . . . .
DOOR MIRROR COVER : Disassembly and As-
sembly . . . . . . . . . . . . . . . . . .
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . .
Revision: 2012 September
2013 MURANO
MIR-3
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2012 September
2013 MURANO
MIR-4
< BASIC INSPECTION >
[WITH ADP]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000008455754
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
CHECK DTC
Perform self-diagnosis for automatic drive positioner (ADP) with CONSULT.
Is any DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 4.
4.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
>> GO TO 5.
5.
IDENTIFY MALFUNCTIONING PARTS WITH “DTC/CIRCUIT DIAGNOSIS”
Perform the diagnosis with “DTC/CIRCUIT DIAGNOSIS” of the applicable system.
>> GO TO 6.
6.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 7.
7.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3.
Are all malfunctions corrected?
YES
>> INSPECTION END
NO
>> GO TO 4.
Revision: 2012 September
2013 MURANO
DOOR MIRROR SYSTEM
MIR-5
< SYSTEM DESCRIPTION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
SYSTEM DESCRIPTION
DOOR MIRROR SYSTEM
System Diagram
INFOID:0000000008455755
System Description
INFOID:0000000008455756
MANUAL FUNCTION
• Door mirror system is composed of automatic drive positioner, door mirror remote control switch and door
mirror.
• Automatic drive positioner control unit controls door mirror.
• Automatic drive positioner control unit receives changeover switch signal and perform the LH/RH control of
door mirror motor that supplies electric power when changeover switch is operated.
• Automatic drive positioner control unit receives mirror switch signal and supplies electric power to door mir-
ror motor when mirror switch is operated.
• The door mirrors can be operated manually when ignition switch is in either ACC or ON position. The ignition
switch signal (ACC/ON) is transmitted from BCM to the driver seat control unit via CAN communication and
from the driver seat control unit to the automatic drive positioner control unit via UART communication.
AUTOMATIC DRIVE POSITIONER SYSTEM LINKED OPERATION
Door mirror control is included in automatic drive positioner system. Refer to automatic drive positioner system
for more details.
Refer to
ADP-13, "AUTOMATIC DRIVE POSITIONER SYSTEM : System Description"
.
JMLIA0006GB
Revision: 2012 September
2013 MURANO
MIR-6
< SYSTEM DESCRIPTION >
[WITH ADP]
DOOR MIRROR SYSTEM
Component Parts Location
INFOID:0000000008455757
Component Description
INFOID:0000000008455758
1.
Door mirror remote control switch
2.
Door mirror (driver side)
3.
Door mirror (passenger side)
4.
Automatic drive positioner control
unit
5.
BCM
6.
Driver seat control unit
A.
View with instrument driver lower
pane removed
B.
Behind the combination meter
C.
Backside of the seat cushion
JMLIA0117ZZ
Component
Function
Automatic drive positioner control unit
Door mirror is supplied with power after receiving the input of the MIRROR
SWITCH and CHANGEOVER SWITCH.
Door mirror remote control
switch
Mirror switch
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSI-
TIONER CONTROL UNIT.
Changeover switch
It transmits the LH/RH control of door mirror that supplies power to AUTO-
MATIC DRIVE POSITIONER CONTROL UNIT.
Door mirror
It makes mirror face operate from side to side and up and down via inte-
grated motor.
BCM
The ignition switch signal (ACC/ON) is transmitted to driver seat control
unit via CAN communication.
Driver seat control unit
The ignition switch signal (ACC/ON) is transmitted to automatic drive posi-
tioner control unit via UART communication.
Revision: 2012 September
2013 MURANO
INSIDE MIRROR SYSTEM
MIR-7
< SYSTEM DESCRIPTION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
INSIDE MIRROR SYSTEM
System Description
INFOID:0000000008455759
The sensor built in inside mirror detects the headlight of the vehicle behind and automatically changes the light
transmission to decrease the brightness.
Component Description
INFOID:0000000008455760
Component
Function
Auto anti-dazzling inside mirror
It automatically changes the light transmittance according to the brightness of the
light from the headlight of the vehicle behind.
Revision: 2012 September
2013 MURANO
MIR-8
< SYSTEM DESCRIPTION >
[WITH ADP]
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
Diagnosis Description
INFOID:0000000008840916
The auto drive positioner system can be checked and diagnosed for component operation with CONSULT.
DIAGNOSTIC MODE
CONSULT Function
INFOID:0000000008840917
SELF-DIAGNOSIS RESULTS
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnostic mode
[AUTO DRIVE POS.]
Description
WORK SUPPORT
Changes the setting of each function.
SELF-DIAG RESULTS
Performs self-diagnosis for the auto drive positioner system and displays the results.
DATA MONITOR
Displays input signals transmitted from various switches and sensors to driver seat con-
trol unit in real time.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST
Drive each output device.
ECU IDENTIFICATION
Displays part numbers of driver seat control unit parts.
Monitor Item
Unit
Main
Signals
Selection
From
Menu
Contents
SET SW
“ON/OFF”
×
×
ON/OFF status judged from the setting switch signal.
MEMORY SW 1
“ON/OFF”
×
×
ON/OFF status judged from the seat memory switch 1 sig-
nal.
MEMORY SW 2
“ON/OFF”
×
×
ON/OFF status judged from the seat memory switch 2 sig-
nal.
SLIDE SW–FR
“ON/OFF”
×
×
ON/OFF status judged from the sliding switch (forward) sig-
nal.
SLIDE SW–RR
“ON/OFF”
×
×
ON/OFF status judged from the sliding switch (backward)
signal.
RECLN SW–FR
“ON/OFF”
×
×
ON/OFF status judged from the reclining switch (forward)
signal.
RECLN SW–RR
“ON/OFF”
×
×
ON/OFF status judged from the reclining switch (backward)
signal.
LIFT FR SW–UP
“ON/OFF”
×
×
ON/OFF status judged from the lifting switch front (up) sig-
nal.
LIFT FR SW–DN
“ON/OFF”
×
×
ON/OFF status judged from the lifting switch front (down)
signal.
LIFT RR SW–UP
“ON/OFF”
×
×
ON/OFF status judged from the lifting switch rear (up) sig-
nal.
LIFT RR SW–DN
“ON/OFF”
×
×
ON/OFF status judged from the lifting switch rear (down)
signal.
MIR CON SW–UP
“ON/OFF”
×
×
ON/OFF status judged from the mirror switch (up) signal.
MIR CON SW–DN
“ON/OFF”
×
×
ON/OFF status judged from the mirror switch (down) signal.
Revision: 2012 September
2013 MURANO
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
MIR-9
< SYSTEM DESCRIPTION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
MIR CON SW–RH
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (passenger side) signal.
MIR CON SW–LH
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (driver side) signal.
MIR CHNG SW–R
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (switching to right) signal.
MIR CHNG SW–L
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (switching to left) signal.
TILT SW-UP
“ON/OFF”
×
×
ON/OFF status judged from the tilt switch (up) signal.
TILT SW-DOWN
“ON/OFF”
×
×
ON/OFF status judged from the tilt switch (down) signal.
TELESCO SW-FR
“ON/OFF”
×
×
ON/OFF status judged from the telescoping switch (for-
ward) signal.
TELESCO SW-RR
“ON/OFF”
×
×
ON/OFF status judged from the telescoping switch (back-
ward) signal.
DETENT SW
“ON/OFF”
×
×
The selector lever position “OFF (P position) / ON (other
than P position)” judged from the detention switch signal.
STARTER SW
“ON/OFF”
×
×
Ignition key switch ON (START, ON) /OFF (ACC, OFF) sta-
tus judged from the ignition switch signal.
SLIDE PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
RECLN PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
LIFT FR PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
LIFT RR PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
MIR/SEN RH U–D
“V”
–
×
Voltage input from door mirror sensor (passenger side) up/
down is displayed.
MIR/SEN RH R–L
“V”
–
×
Voltage input from door mirror sensor (passenger side) left/
right is displayed.
MIR/SEN LH U–D
“V”
–
×
Voltage input from door mirror sensor (driver side) up/down
is displayed.
MIR/SEN LH R–L
“V”
–
×
Voltage input from door mirror sensor (driver side) left/right
is displayed.
TILT PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
TELESCO PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
VEHICLE SPEED
—
×
×
Display the vehicle speed signal received from combination
meter by numerical value [km/h].
P RANG SW CAN
“ON/OFF”
×
×
ON/OFF status judged from the P range switch signal.
R RANGE (CAN)
“ON/OFF”
×
×
ON/OFF status judged from the R range switch signal.
DOOR SW–FL
“ON/OFF”
×
×
ON/OFF status judged from the door switch (front driver
side) signal.
DOOR SW–FR
“ON/OFF”
×
×
ON/OFF status judged from the door switch (front passen-
ger side) signal.
Monitor Item
Unit
Main
Signals
Selection
From
Menu
Contents
Revision: 2012 September
2013 MURANO
MIR-10
< SYSTEM DESCRIPTION >
[WITH ADP]
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
ACTIVE TEST
CAUTION:
When driving vehicle, do not perform active test.
WORK SUPPORT
IGN ON SW
“ON/OFF”
×
×
ON/OFF status judged from the ignition switch signal.
ACC ON SW
“ON/OFF”
×
×
ON/OFF status judged from the ACC switch signal.
KEY ON SW
“ON/OFF”
×
×
ON/OFF status judged from the key on switch signal.
KEYLESS ID
—
×
×
Key ID status judged from the key ID signal.
KYLS DR UNLK
“ON/OFF”
×
×
ON/OFF status judged from the driver side door unlock ac-
tuator output switch signal.
VHCL SPEED (ABS)
“ON/OFF”
×
×
ON/OFF status judged from vehicle speed signal.
HANDLE
“RHD/LHD”
×
×
RHD/LHD status judged from handle position signal.
TRANSMISSION
“AT or CVT/
MT”
×
×
AT or CVT/MT status judged from transmission.
STEERING STATUS
NOTE:
This item is displayed, but cannot monitored
Monitor Item
Unit
Main
Signals
Selection
From
Menu
Contents
Test item
Description
SEAT SLIDE
Activates/deactivates the sliding motor.
SEAT RECLINING
Activates/deactivates the reclining motor.
SEAT LIFTER FR
Activates/deactivates the lifting motor (front).
SEAT LIFTER RR
Activates/deactivates the lifting motor (rear).
TILT MOTOR
Activates/deactivates the tilt motor.
TELESCO MOTOR
Activates/deactivates the telescopic motor.
MIRROR MOTOR RH
Activates/deactivates the mirror motor (passenger side).
MIRROR MOTOR LH
Activates/deactivates the mirror motor (driver side).
MEMORY SW INDCTR
Turns ON/OFF the memory indicator.
Work item
Content
Item
SEAT SLIDE VOLUME SET
The amount of seat sliding for entry/exit assist can be selected
from 3 items.
40 mm
80 mm
150 mm
EXIT TILT SETTING
Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)
ON
OFF
EXIT SEAT SLIDE SETTING
Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)
ON
OFF
Revision: 2012 September
2013 MURANO
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-11
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH
MIRROR SWITCH
MIRROR SWITCH : Description
INFOID:0000000008455763
It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.
MIRROR SWITCH : Component Function Check
INFOID:0000000008455764
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
MIR-11, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000008455765
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
Monitor item
Condition
MIR CON SW-UP/DN
When operating the mirror switch toward the up or down side.
: ON
Other than above.
: OFF
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
4
Ground
5
12
13
15
Revision: 2012 September
2013 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст