Nissan Juke F15. Manual — part 222
DLK-68
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000012196627
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-68, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000012196628
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) connector.
3. Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock assembly connector.
2. Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLK
UNLOCK
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock assembly
(driver side)
Connector
Terminal
D38
2
Ground
Door lock and unlock switch
Unlock
12 V
1
Lock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M69
65
D38
1
Existed
66
2
BCM
Ground
Continuity
Connector
Terminal
M69
65
Not existed
66
DOOR LOCK ACTUATOR
DLK-69
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000012196629
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-68, "DRIVER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000012196630
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (passenger side) connector.
3. Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock assembly connector.
2. Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
66
Ground
Door lock and unlock switch
Unlock
12 V
65
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLK
UNLOCK
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock assembly
(passenger side)
Connector
Terminal
D17
6
Ground
Door lock and unlock switch
Unlock
12 V
5
Lock
DLK-70
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
REAR LH
REAR LH : Component Function Check
INFOID:0000000012196631
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-68, "DRIVER SIDE : Diagnosis Procedure"
REAR LH : Diagnosis Procedure
INFOID:0000000012196632
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock assembly LH connector.
3. Check voltage between rear door lock assembly LH harness connector and ground.
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69
59
D17
6
Existed
65
5
BCM
Ground
Continuity
Connector
Terminal
M69
59
Not existed
65
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
59
Ground
Door lock and unlock switch
Unlock
12 V
65
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLK
UNLOCK
DOOR LOCK ACTUATOR
DLK-71
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock assembly connector.
2. Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
REAR RH
REAR RH : Component Function Check
INFOID:0000000012196633
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock assembly LH
Connector
Terminal
D65
2
Ground
Door lock and unlock switch
Unlock
12 V
1
Lock
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B10
55
D65
2
Existed
M69
65
1
BCM
Ground
Continuity
Connector
Terminal
B10
55
Not existed
M69
65
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B10
55
Ground
Door lock and unlock switch
Unlock
12 V
M69
65
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLK
UNLOCK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст