Nissan Juke F15. Manual — part 81
BCS
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
BCS-79
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description
INFOID:0000000012200723
Perform the following operations when replacing BCM. (For details, refer to
.)
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “Read / Write Configuration” or “Manual Configuration” with
CONSULT. Or not doing so, BCM control function does not operate normally.
• Complete the procedure of “Read / Write Configuration” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “Read / Write Configuration” or “Manual Configuration”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NVIS) (if equipped).
Work Procedure
INFOID:0000000012200724
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU” of “Read / Write Configuration” to save or print current vehicle specification.
NOTE:
If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
BCS-94, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “After Replace ECU” of “Read / Write Configuration” or “Manual Configuration” to write vehicle speci-
fication. Refer to
>> GO TO 4.
4.
INITIALIZE BCM (NVIS) (IF EQUIPPED)
Perform BCM initialization. (NVIS)
>> WORK END
BCS-80
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
CONFIGURATION (BCM)
Description
INFOID:0000000012200725
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows. (For details, refer to
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting cannot be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “Re/programming, Configuration” with CONSULT. Or not doing
so, BCM control function does not operate normally.
• Complete the procedure of “Read / Write Configuration” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Read / Write Configuration” except for new BCM.
• If you set incorrect “Read / Write Configuration”, incidents might occur.
Work Procedure
INFOID:0000000012200726
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “Re/programming, Configuration” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “AFTER REPLACE ECU” OF “READ / WRITE CONFIGURATION”
CONSULT Configuration
Perform “After Replace ECU” of “Read / Write Configuration”.
>> WORK END
3.
PERFORM “MANUAL CONFIGURATION”
CONSULT Configuration
1. Select “Manual Configuration”.
2. Identify the correct model and configuration list. Refer to
.
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “Next”. Refer to
for written items and setting
value.
4. Touch “Next”.
5. Touch “OK”.
CAUTION:
Make sure to select “OK” even if the indicated configuration of brand new BCM is same as the
desirable configuration. If not, configuration which is set automatically by selecting vehicle model
cannot be memorized.
6. Check that the configuration has been successfully written and touch “End”.
Function
Description
Read / Write Configuration
Before Replace ECU
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
After Replace ECU
Writes the vehicle configuration with saved data.
Manual Configuration
Writes the vehicle configuration with manual selection.
BCS
CONFIGURATION (BCM)
BCS-81
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration list
INFOID:0000000012200727
CAUTION:
• Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
• The “setting value” of this vehicle is as follows: Never select any other value than the setting value
shown below. (If there is only 1 item in “setting value” that means that item is the only choice for this
certain vehicle.)
⇔: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
AUTO LIGHT
WITH
⇔ WITHOUT
• WITH: With auto light system
• WITHOUT: Without auto light system
DTRL
WITHOUT
⇔ MODE1 ⇔ MODE2
• WITHOUT: Without daytime running light system
• MODE1: With daytime running light system (For NISMO
models)
• MODE2: With daytime running light system (Except for NIS-
MO models)
TRANSMISSION
AT with ABS
⇔ MT with ABS
• AT with ABS: Except M/T models
• MT with ABS: M/T models
BCM AC CONTROL
MODE2
⇔ MODE4
• MODE2: Manual air conditioning system
• MODE4: Automatic air conditioning system
DONGLE
WITH
⇔ WITHOUT
• WITH: For Canada models
• WITHOUT: Except for Canada models
TIRE PRESSURE
230kPa
⇔ 240kPa ⇔ 250kPa
• 230kPa: 2WD M/T models
• 240kPa: AWD models
• 250kPa: 2WD except M/T models
BCS-82
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
SHIPPING MODE CANCEL OPERATION
SHIPPING MODE CANCEL OPERATION
Description
INFOID:0000000012200728
SYSTEM DIAGRAM
DESCRIPTION
• The combination meter transmits meter CAN signal*
1
to BCM via CAN communication, when the extended
storage fuse switch is ON.
• BCM switches the status (shipping mode or normal mode) by itself according to the meter CAN signal*
1
from
combination meter, and transmits shipping mode status signal to combination meter via CAN communica-
tion.
• The combination meter displays extended storage fuse warning message*
2
on the odometer display, when
BCM is in shipping mode.
• BCM control functions are limited in shipping mode. Refer to
*1: Odometer signal, wake up signal and each signal.
*2: When shipping mode function operates, “SHIP
→PHASE→On→PUSH→FUSE In” is displayed.
Work Procedure
INFOID:0000000012200729
1.
SHIPPING MODE CANCEL OPERATION
1. Turn ignition switch OFF.
2. Push in (switch on) the extended storage fuse switch. Refer to
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.
SHIPPING MODE CANCEL CHECK
1. Turn ignition switch ON.
2. Check that extended storage fuse warning message is not displayed on odometer display.
>> WORK END
JMMIA1311GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст