Nissan Juke F15. Manual — part 1208
TM-22
< PERIODIC MAINTENANCE >
[6MT: RS6F94R]
GEAR OIL
PERIODIC MAINTENANCE
GEAR OIL
Inspection
INFOID:0000000012200760
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
1. Remove filler plug (1) and gasket from transaxle case.
2. Check the oil level from filler plug mounting hole as shown in the
figure.
CAUTION:
Never start engine while checking oil level.
3. Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4. Tighten filler plug to the specified torque. Refer to
Draining
INFOID:0000000012200761
1. Start engine and let it run to warm up transaxle.
2. Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.
3. Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].
CAUTION:
Never reuse gasket.
4. Tighten drain plug to the specified torque. Refer to
Refilling
INFOID:0000000012200762
1. Remove filler plug (1) and gasket from transaxle case.
2. Fill with new gear oil until oil level reaches the specified limit at
filler plug mounting hole as shown in the figure.
3. After refilling gear oil, check the oil level. Refer to
4. Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
5. Tighten filler plug to the specified torque. Refer to
SCIA7623E
SCIA7622E
Oil grade and
viscosity
: Refer to
MA-11, "Fluids and Lubricants"
Oil capacity
: Refer to
SCIA7623E
SIDE OIL SEAL
TM-23
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Removal and Installation
INFOID:0000000012200763
REMOVAL
1. Remove front drive shafts. Refer to
FAX-83, "2WD : Removal and Installation"
.
2. Remove differential side oil seals (1) from clutch housing and
transaxle case, using an oil seal remover.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle
case, using the drift [Stamping number: B.vi 1666-B] of the drift set
[SST: KV32500QAA ( - )].
CAUTION:
• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
Inspection
INFOID:0000000012200764
INSPECTION AFTER INSTALLATION
Check the oil level and oil leakage. Refer to
.
SCIA7625E
A
: Transaxle case side
B
: Clutch housing side
Dimension “L
1
”
: 1.2 – 1.8 mm (0.047 – 0.071 in)
Dimension “L
2
”
: 2.7 – 3.3 mm (0.106 – 0.130 in)
JPDIC0454ZZ
TM-24
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
POSITION SWITCH
POSITION SWITCH
Removal and Installation
INFOID:0000000012200765
REMOVAL
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Disconnect position switch connector.
3. Remove position switch from transaxle case.
INSTALLATION
1. Apply recommended sealant to threads of position switch.
• Use Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products
CAUTION:
Remove old sealant and oil adhering to threads.
2. Install position switch to transaxle case.
3. Tighten position switch to the specified torque. Refer to
4. For the next step and after, install in the reverse order of removal.
Inspection
INFOID:0000000012200766
INSPECTION AFTER INSTALLATION
• Check continuity between position switch terminals. Refer to
TM-20, "BACK-UP LAMP SWITCH : Compo-
(Back-up lamp switch) and
TM-20, "PARK/NEUTRAL POSITION (PNP) SWITCH : Compo-
(PNP switch).
• Check the oil leakage. Refer to
CONTROL LINKAGE
TM-25
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL LINKAGE
Exploded View
INFOID:0000000012200767
Removal and Installation
INFOID:0000000012200768
REMOVAL
1. Shift the shifter lever to the neutral position.
2. Remove air cleaner case. Refer to
EM-192, "Removal and Installation"
.
1.
Bracket
2.
Shifter cable
3.
Selector lever
4.
Shifter lever A
5.
Tapping bolt
6.
Cable mounting bracket
7.
Selector cable
8.
Grommet
9.
M/T shift selector assembly
10. Shifter lever
11. Shifter lever knob
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPDIC0830GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст