Nissan Juke F15. Manual — part 1185
STEERING GEAR AND LINKAGE
ST-17
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Removal and Installation
INFOID:0000000012200348
REMOVAL
1. Set vehicle to the straight-ahead position.
2. Remove intermediate shaft mounting bolt (steering gear assembly side). Refer to
.
CAUTION:
• Spiral cable may be cut if steering wheel turns while separating steering column assembly and
steering gear assembly. Always fix the steering wheel using string to avoid turning.
• Place a matching mark on both intermediate shaft and steering gear assembly before removing
intermediate shaft.
• When removing intermediate shaft, never insert a tool, such as a screwdriver, into the yoke
groove to pull out the intermediate shaft. In case of the violation of the above, replace intermedi-
ate shaft with a new one.
3. Remove dash seal from vehicle. Refer to
ST-14, "Removal and Installation"
.
4. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
1.
Outer socket
2.
Boot clamp (small diameter)
3.
Boot
4.
Boot clamp (large diameter)
5.
Gear housing assembly
6.
Dust cover
1: Apply Genuine Lithium Soap, Autorex A (manufactured by Kyodo yushi) or equivalent.
2: Apply Genuine Lithium Soap, Wanlouver No.2 (manufactured by Kyodo yushi) or equivalent.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPGIA0145GB
ST-18
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
5. Remove steering outer socket from steering knuckle so as not to
damage ball joint boot using suitable ball joint remover (com-
mercial service tool).
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the ball joint remover from sudden drop
turning.
6. Remove front suspension member. Refer to
7. Remove steering gear assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Always fix the steering wheel using string to avoid turning.
• Perform final tightening of nuts and bolts on each part under unladen conditions with tires on level ground
when removing steering gear assembly. Check wheel alignment. Refer to
• Rotate steering wheel to check for decentered condition, binding, noise or excessive steering effort.
• Never reuse steering outer socket mounting nut and steering gear assembly mounting nut.
• Perform inspection after installation. Refer to
.
Disassembly and Assembly
INFOID:0000000012200349
DISASSEMBLY
1. Loosen outer socket lock nut, and remove outer socket.
CAUTION:
When loosening lock nut, be sure to fix outer socket with a wrench or an equivalent.
2. Remove boot clamps, and then remove boot from inner socket.
CAUTION:
Never damage inner socket part and gear housing part of steering gear assembly when removing
boot. steering gear assembly must be replaced if steering gear assembly are damaged because it
may cause foreign material interfusion.
3. Remove dust cover.
4. Perform inspection after disassembly. Refer to
.
ASSEMBLY
1. Apply recommended grease to the entire inner perimeter (A) of
the dust cover lip and contact surface (B) of the gear housing
part, and install dust cover to steering gear assembly.
Use Genuine Lithium Soap, Wanlouver No.2 (manufactured
by Kyodo yushi) or equivalent.
SGIA0184J
JPGIA0103ZZ
STEERING GEAR AND LINKAGE
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2. Apply recommended grease to inner socket (A) of gear housing
assembly and install boot to gear housing assembly.
Use Genuine Lithium Soap, Autorex A (manufactured by
Kyodo yushi) or equivalent.
CAUTION:
Never reuse boot.
3. Install boot clamp (large diameter) (1) to boot using boot band
crimping tool (A) [SST: KV40107300 (
—
)].
CAUTION:
• Never reuse boot clamp (large diameter).
• Install boot clamp (large diameter) (1) securely to boot
groove, and crimp it so as to have clearance (B) of 3 mm
(0.12 in) or less as shown.
4. Install boot clamp (small diameter) to boot.
CAUTION:
Never reuse boot clamp (small diameter).
5. Adjust inner socket to standard length (L), and then tighten lock
nut (1) to the specified torque. Check length again after tighten-
ing lock nut.
CAUTION:
• When tightening the lock nut (1), be sure to fix outer
socket (2) with a wrench or an equivalent to prevent the
ball joint from getting contact with the knuckle.
• Adjust toe-in after this procedure. The length achieved
after toe-in adjustment is not necessary the above value.
Inspection
INFOID:0000000012200350
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks, and replace it if a malfunction is detected.
Gear housing assembly
• Check gear housing assembly for damage and scratches. Replace if there are any abnormal conditions.
Outer Socket and Inner Socket
• Check the following items and replace the component if it does not meet the standard.
Grease application position (Reference)
A
: 10 mm (0.39 in)
JPGIA0102ZZ
JSGIA0140ZZ
Inner socket length (L)
: Refer to
.
JPGIA0187ZZ
JSGIA0538ZZ
ST-20
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
BALL JOINT SWINGING FORCE
• Hook a spring balance at the point shown in the figure and pull the
spring balance. Make sure that the spring balance reads the spec-
ified value when ball stud and inner socket start to move. Replace
outer socket or steering gear assembly (inner socket) if they are
outside the standard.
BALL JOINT AXIAL END PLAY
• Apply an axial load of 490 N (50 kg, 110 lb) to ball stud. Using a
dial gauge, measure amount of stud movement, and then make
sure that the value is within the following specified range. Replace
outer socket (1) steering gear assembly (inner socket) (2) if the
measured value is outside the standard.
INSPECTION AFTER INSTALLATION
• Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Adjust neutral position of steering angle sensor. Refer to
.
Outer socket
(Measuring point of outer socket: Ball stud upper side)
: Refer to
ST-21, "Steering Gear and Linkage"
Inner socket
(Measuring point of inner socket: “*” mark shown in the
figure)
: Refer to
ST-21, "Steering Gear and Linkage"
Outer socket : Refer to
ST-21, "Steering Gear and Link-
Inner socket
ST-21, "Steering Gear and Link-
SGIA0896E
JSGIA0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст