Nissan Juke F15. Manual — part 1103
UPPER LINK
RSU-33
< REMOVAL AND INSTALLATION >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UPPER LINK
Exploded View
INFOID:0000000012200425
Removal and Installation
INFOID:0000000012200426
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and
.
3. Set jack under suspension arm.
CAUTION:
• Never damage the suspension arm with a jack.
• Check the stable condition when using a jack.
4. Remove eccentric disc, adjusting bolt, mounting bolt, and nut, then remove upper link.
5. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
• Never reuse upper link mounting nut.
• Perform inspection after installation. Refer to
1.
Rear suspension member
2.
Adjusting bolt
3.
Upper link
4.
Eccentric disk
5.
Lower link
6.
Suspension arm bracket
7.
Suspension arm
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPEIB0262GB
RSU-34
< REMOVAL AND INSTALLATION >
[AWD]
UPPER LINK
Inspection
INFOID:0000000012200427
INSPECTION AFTER REMOVAL
Check upper link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
.
2. Check wheel alignment. Refer to
3. Adjust neutral position of steering angle sensor. Refer to
.
REAR STABILIZER
RSU-35
< REMOVAL AND INSTALLATION >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000012200428
Removal and Installation
INFOID:0000000012200429
REMOVAL
1. Remove stabilizer link.
2. Remove center muffler. Refer to
EX-10, "Removal and Installation"
3. Remove mounting nuts on stabilizer clamp, bushing, and stabilizer bar from suspension member.
4. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
• Never reuse stabilizer link mounting nut.
Inspection
INFOID:0000000012200430
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer link, stabilizer bushing and stabilizer clamp for deformation, cracks or damage.
Replace it if necessary.
1.
Stabilizer bar
2.
Bushing
3.
Stabilizer clamp
4.
Stabilizer link
5.
Lower link
6.
Rear suspension member
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPEIB0263GB
RSU-36
< REMOVAL AND INSTALLATION >
[AWD]
REAR SUSPENSION ASSEMBLY
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000012200431
Removal and Installation
INFOID:0000000012200432
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove center muffler. Refer to
EX-10, "Removal and Installation"
3. Remove propeller shaft. Refer to
DLN-124, "Removal and Installation"
.
4. Remove stabilizer bar. Refer to
RSU-35, "Removal and Installation"
.
5. Remove wheel sensor and sensor harness. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and
.
6. Remove upper link from suspension arm. Refer to
RSU-33, "Removal and Installation"
.
7. Remove lower link from suspension arm. Refer to
RSU-31, "Removal and Installation"
8. Remove drive shaft from rear final drive. Refer to
RAX-19, "Removal and Installation"
.
9. Remove rear final drive. Refer to
DLN-151, "Removal and Installation"
10. Set jack under rear suspension member.
CAUTION:
• Never damage the suspension member with a jack.
• Check the stable condition when using a jack.
11. Remove rear suspension member mounting bolts, rebound stopper, and washer.
12. Slowly lower jack, then remove rear suspension member, lower link and upper link from vehicle as a unit.
CAUTION:
Operate while checking that jack supporting status is stable.
13. Remove lower link and upper link from rear suspension member.
14. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of the removal.
1.
Rear suspension member
2.
Rebound stopper
3.
Washer
: Vehicle front
: N·m (kg-m, ft-lb)
JPEIB0264GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст