Nissan Juke F15. Manual — part 794
FL-6
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
REMOVAL AND INSTALLATION
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000012197583
REMOVAL
DISASSEMBLY
1.
Rock ring
2.
Fuel level sensor unit, fuel filter and
fuel pump assembly
3.
O-ring
4.
Fuel tank
Vehicle front
: Always replace after every disassembly.
JPBIA4872ZZ
1.
Fuel filter and fuel pump assembly
2.
Fuel level sensor unit
JPBIA4226ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2WD : Removal and Installation
INFOID:0000000012197584
WARNING:
Read “General Precautions” when working on the fuel system. Refer to
.
REMOVAL
1. Release the fuel pressure from the fuel lines. Refer to
.
2. Check fuel level on a level ground. If the fuel level is 7/8 of the fuel tank (full or nearly full), draw appropri-
ate amount of fuel from the fuel tank.
• In the event of malfunction in fuel pump, insert a hose measuring 25 mm (0.98 in) in diameter into the
filler opening to draw approximately 25 liters fuel.
3. Open fuel filler lid.
4. Open filler cap and release the pressure inside fuel tank.
5. Remove rear seat. Refer to
6. Remove inspection hole cover.
7. Disconnect harness connector (1) and quick connector (2).
• Remove quick connector in the following procedures.
- Pinch quick connector square-part (A) with your fingers, and
pull out the quick connector (1) by hand.
- If quick connector and tube on sender unit are stuck, push and
pull several times until they move, and pull out.
CAUTION:
• Quick connector can be removed when the tabs are com-
pletely depressed. Never twist it more than necessary.
• Never use any tools to disconnected quick connector.
• Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Never bend or twist resin tube during installation and disconnection.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
• Never insert plug, preventing damage on O-ring in quick
connector.
Guideline
Draw approximately 25 liters (6-5/8 US gal, 5-1/4 Imp gal) from a full-tank
condition.
3
: Fuel feed hose
4
: Fuel level sensor unit, fuel filter and fuel pump assembly
: Vehicle front
JPBIA4461ZZ
JPBIA4462ZZ
JPBIA2889ZZ
FL-8
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
8. Remove lock ring for fuel level sensor unit, fuel filter and fuel
pump assembly with lock ring wrench (A) by turning counter-
clockwise.
NOTE:
For reference when installing, put a matching mark on lock ring,
fuel pump assembly and fuel tank.
9. Raise fuel level sensor unit, fuel filter and fuel pump assembly
(1).
CAUTION:
• Never bend float arm during removal.
• Never pollute the inside by residue fuel. Draw out avoid-
ing inclination by supporting with a cloth.
• Never cause impacts such by dropping when handling
components.
INSTALLATION
Note to the following, and install in the reverse order of removal.
CAUTION:
Do not reuse O-rings.
1. Install O-ring to fuel tank without twist.
CAUTION:
Do not reuse O-ring.
2. Install fuel level sensor unit, fuel filter and fuel pump assembly
(1) with its matching mark (A) aligned with fuel tank matching
mark (B) as shown in the figure.
CAUTION:
Never bend float arm during installing.
3. Install lock ring for fuel level sensor unit, fuel filter and fuel pump
assembly with lock ring wrench (A) by turning clockwise.
4. Connect quick connector of fuel feed tube as per following procedures.
a. Check the connection for damage or any foreign materials.
b. Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
Tool number (A)
: KV991J0090 (J-46214) (shown)
: KV101207S0 ( — )
JPBIA4463ZZ
JPBIA4464ZZ
: Vehicle front
JPBIA4469ZZ
Tool number (A)
: KV991J0090 (J-46214) (shown)
: KV101207S0 ( — )
JPBIA4463ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
c. After connecting, check that the connection is secure by following method.
• Visually confirm that the two tabs are connected to the connector.
• Pull (A) the tube and the connector to check they are securely
connected.
2WD : Disassembly and Assembly
INFOID:0000000012197585
DISASSEMBLY
1. Disconnect harness connector (A).
2. Press (A) with a flat-blade screwdriver or an equivalent to
release lock and push out the fuel level sensor unit (1).
3. To remove the fuel level sensor unit (1), side it in the direction
(
) of the arrow with the lock release.
ASSEMBLY
1. Check for damage of fuel level sensor unit installation position on the side of fuel filter and pump assem-
bly.
2. Slide fuel level sensor unit until it aligns to installation groove, then insert it until stops.
• After inserting, apply force in reverse direction (removal direction) to ensure it cannot be pulled out.
3. Connect harness connector.
1
: Quick connector
JPBIA2893ZZ
JPBIA4471ZZ
JPBIA4472ZZ
JPBIA4473ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст