Nissan Juke F15. Manual — part 484
ADDITIONAL SERVICE WHEN REPLACING ECM
EC-749
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ADDITIONAL SERVICE WHEN REPLACING ECM
Description
INFOID:0000000012198255
When replacing ECM, the following procedure must be performed. (For details, refer to
.)
PROGRAMMING OPERATION
NOTE:
After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the pro-
cedure to perform the programming.
Work Procedure
INFOID:0000000012198256
1.
SAVE ECM DATA
With CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Turn ignition switch ON.
4. Select “SAVING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
5. Follow the instruction of CONSULT display.
NOTE:
Necessary data in ECM is copied and saved to CONSULT.
>> GO TO 2.
2.
CHECK ECM PART NUMBER
Check ECM part number to see whether it is blank ECM or not.
NOTE:
• Part number of blank ECM is 23703 -
×××××.
• Check the part number when ordering ECM or with the one included in the label on the container box.
Is the ECM a blank ECM?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
SAVE ECM PART NUMBER
Read out the part number from the old ECM and save the number, following the programming instructions.
Refer to “CONSULT Operation Manual”.
NOTE:
• The ECM part number is saved in CONSULT.
• Even when ECM part number is not saved in CONSULT, go to 4.
>> GO TO 4.
4.
PERFORM ECM PROGRAMMING
After replacing ECM, perform the ECM programming. Refer to “CONSULT Operation Manual”.
NOTE:
• Refer to
EC-1256, "Removal and Installation"
for replacement of ECM.
• During programming, maintain the following conditions:
- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 – 13.5 V (Be sure to check the value of battery voltage by selecting “BATTERY VOLT” in
“Data monitor” of CONSULT.)
>> GO TO 6.
5.
REPLACE ECM
EC-750
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
ADDITIONAL SERVICE WHEN REPLACING ECM
>> GO TO 6.
6.
WRITE ECM DATA
With CONSULT
1. Select “WRITING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
2. Follow the instruction of CONSULT display.
NOTE:
The data saved by “SAVE DATA FOR CPU REPLC” is written to ECM.
>> GO TO 7.
7.
PERFORM VIN REGISTRATION
.
>> GO TO 8.
8.
PERFORM INITIALIZATION OF NATS SYSTEM AND REGISTRATION OF ALL NATS IGNITION KEY IDS
>> GO TO 9.
9.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
.
>> GO TO 10.
10.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
.
>> GO TO 11.
11.
PERFORM WASTEGATE VALVE CLOSED POSITION LEARNING
Perform wastegate valve closed position learning. Refer to
>> GO TO 12.
12.
PERFORM IDLE AIR VOLUME LEARNING
.
>> GO TO 13.
13.
PERFORM AIR FUEL RATIO INITIAL LEARNING
Perform air fuel ratio initial learning. Refer to
.
>> GO TO 14.
14.
PERFORM G SENSOR CALIBRATION
.
>> GO TO 15.
15.
PERFORM VALVE TIMING OFFSET DATA CLEAR
Perform valve timing offset data clear. Refer to
>> GO TO 16.
ADDITIONAL SERVICE WHEN REPLACING ECM
EC-751
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
16.
PERFORM VALVE TIMING OFFSET DATA WRITING
Perform valve timing offset data writing. Refer to
>> END
EC-752
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
VIN REGISTRATION
VIN REGISTRATION
Description
INFOID:0000000012198257
VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M).
Work Procedure
INFOID:0000000012198258
1.
CHECK VIN
Check the VIN of the vehicle and note it. Refer to
GI-36, "Information About Identification or Model Code"
>> GO TO 2.
2.
PERFORM VIN REGISTRATION
With CONSULT
1. Turn ignition switch ON and engine stopped.
2. Select “VIN REGISTRATION” in “WORK SUPPORT” mode of “ENGINE”.
3. Follow the instruction of CONSULT display.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст