Nissan Juke F15. Manual — part 1319
TM-466
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
8. Stop the vehicle.
9. Check the first trip DTC.
With GST
1. Turn ignition switch OFF and cool the engine.
2. Start the engine and wait for at least 2 minutes.
3. Drive the vehicle and maintain the following conditions for 20 minutes or more.
4. Stop the vehicle.
CAUTION:
Never turn ignition switch OFF
5. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO
>> GO TO 8.
8.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
YES-2 >> Confirmation after repair: INSPECTION END
NO
>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to
TM-577, "Removal and Installation"
Diagnosis Procedure
INFOID:0000000012201167
1.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
0
°C (32°F) – 9°C (48.2°F)
7 minutes or more
Other than the above
— (Go to “8.CHECK CVT FLU-
ID TEMPERATURE SENSOR”)
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT fluid temperature before engine start
Driving time
CVT unit
Condition
Resistance
(Approx.)
Terminal
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
CVT unit
Condition
Resistance
(Approx.)
Connector
Terminal
F250
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-467
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)
1. Disconnect the TCM connector.
2. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
4.
CHECK DTC (TCM)
With CONSULT
1. Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0711” detected?
YES
>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.
TM-577, "Removal and Installation"
.
NO
>> INSPECTION END
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F83
11
F82
18
Existed
12
12
TCM
—
Continuity
Connector
Terminal
F83
11
Ground
Not existed
12
TM-468
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000012201168
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for 10 seconds or more.
2. Check the first trip DTC.
Is “P0712” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201169
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning part.
2.
CHECK CVT UNIT TERMINAL CODE ASSEMBLY
Check continuity between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> There is a malfunction of the CVT unit terminal code assembly. Replace the transaxle assembly.
TM-577, "Removal and Installation"
.
3.
CHECK CVT FLUID TEMPERATURE SENSOR
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0712
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Low)
When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Fluid temperature sensor detection voltage:
0.15 V or less
• Harness or connector
(CVT fluid temperature sensor circuit is
shorted to ground)
• CVT fluid temperature sensor
TCM
—
Continuity
Connector
Terminal
F83
12
Ground
Not existed
CVT unit
—
Continuity
Connector
Terminal
F82
12
Ground
Not existed
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-469
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.
TM-577, "Removal and Installation"
.
CVT unit
Condition
Resistance
(Approx.)
Connector
Terminal
F250
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст