Nissan Juke F15. Manual — part 1379
WW-12
< SYSTEM DESCRIPTION >
SYSTEM
1. More than 1 minute is passed after the rear wiper stop.
2. Turn rear wiper switch OFF.
3. Operate the rear wiper switch or rear washer switch.
DIAGNOSIS SYSTEM (BCM)
WW-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000012946846
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
WW-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000012197046
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF
→ ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DIAGNOSIS SYSTEM (BCM)
WW-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
− 7]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Output the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop the rear wiper motor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст