Nissan Juke F15. Manual — part 175
CL-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000012199540
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000012199541
Tool number
(TechMate No.)
Tool name
Description
ST20050240
( — )
Diaphragm adjusting wrench
Adjusting unevenness of diaphragm spring le-
ver
ZZA0508D
Tool name
Description
Clutch aligner
Installing clutch disc
MCIB0404E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
CL-5
< SYMPTOM DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000012199542
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If nec-
essary, repair or replace these parts.
SUSPECTED PARTS (Possible cause)
CLUTCH P
E
DAL (I
ns
pe
ct
ion
a
nd
ad
ju
stm
en
t)
CLUTCH LINE (A
ir in line)
ENGINE MOU
NTING (Loose)
CSC (Con
ce
nt
ric
Sla
ve
Cy
lin
de
r) (W
orn
, d
irty
or
da
ma
ge
d)
CLUTCH DISC (Out
of
true)
CLUTCH DISC (Runou
t i
s ex
ce
ssi
ve
)
CLUTCH DISC (Lining
broken)
CLUTCH DISC (Dirty or burned)
CLUTCH DISC (Oily)
CLUTCH DISC (W
orn out)
CLUTCH DISC (Hardened)
CLUTCH DISC (Lack of
s
pl
ine
g
rea
se
)
DI
APHRAGM SPRI
N
G (Dam
ag
ed
)
DIAPHRAGM
SPRING (Ou
t of
ti
p a
lig
nm
en
t)
PRESSURE P
LA
T
E (Di
st
orti
on)
FL
YWHE
EL (Di
stortion)
Reference
(Except
for
NISMO
RS),
(For NISMO RS)
(Except
for
NISMO
RS),
(For N
ISMO
RS
)
Symptom
Clutch grabs/chatters
1
2
2
2
2
2
Clutch pedal spongy
1
2
Clutch noisy
1
Clutch slips
1
2
2
3
4
5
Clutch does not disengage
1
2
3
3
3
3
3
3
3
4
4
5
CL-6
< PERIODIC MAINTENANCE >
CLUTCH PEDAL
PERIODIC MAINTENANCE
CLUTCH PEDAL
Inspection and Adjustment
INFOID:0000000012199543
INSPECTION
The Height of Clutch Pedal
1. Turn the floor carpet.
2. Check that the clutch pedal height “H
1
” from the dash lower
panel (1) is within the reference value.
3. Replace clutch pedal if the height is outside the reference value.
Clutch Pedal Height When Disengaging The Clutch
1. Securely engage the parking brake.
2. Turn the floor carpet.
3. Start the engine and run at idle.
4. Fully depress clutch pedal and shift to the 1st gear.
CAUTION:
Securely depress the brake pedal with shifter lever in 1st gear.
5. Gradually release the clutch pedal and check that the clutch
pedal height “H
2
” from the dash lower panel (1) is within the ref-
erence value with a scale immediately before the clutch is
engaged.
NOTE:
Although the clutch pedal height differs according to whether the
clutch gets disengaged or engaged, clutch-engaged case is
regarded as clutch-disengaged case for easier inspection.
6. Replace clutch pedal if the height is outside the reference value.
Clutch Pedal Play
1. Push the pedal pad by hand until a resistance can be felt and
check that the play “A” on the upper surface of the pedal pad is
within the reference value.
2. Replace clutch pedal if the play is outside the reference value.
Position of Clutch Interlock Switch
Clutch pedal height
“H
1
”
.
JPFIA0065ZZ
Clutch pedal height at
clutch disengagement
“H
2
”
: Refer to
JPFIA0068ZZ
Clutch pedal play “A” : Refer to
.
JPFIA0121ZZ
CLUTCH PEDAL
CL-7
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
Check that the clearance “C” between the thread end of clutch inter-
lock switch (1) and stopper rubber (2) is within the specified value
while clutch pedal is fully depressed.
Position of Clutch Pedal Position Switch
Check that the clearance “A” between the thread end of clutch pedal
position switch (1) and clutch pedal (2) is within the specified value
while clutch pedal is fully released.
ADJUSTMENT
Position of Clutch Interlock Switch
1. Disconnect the clutch interlock switch connector.
2. Loosen the clutch interlock switch 45 degrees counterclockwise.
3. With the clutch pedal fully depressed, press into the clutch inter-
lock switch (1) until it reaches the stopper rubber (2) and turn the
switch clockwise by 45 degrees to secure it.
CAUTION:
The clearance “C” show in the figure must be within the
specified value.
NOTE:
Fully depressed clutch pedal means a clutch pedal condition
that the clutch pedal lever contacts the pedal stopper rubber.
Position of Clutch Pedal Position Switch
1. Disconnect the clutch pedal position switch connector.
2. Loosen the clutch pedal position switch 45 degrees counterclockwise.
3. Press-fit the clutch pedal position switch (1) until the clutch
pedal position switch hits the clutch pedal (2) 45 degrees clock-
wise while pulling the pedal pad slightly.
CAUTION:
The clearance “A” show in the figure must be within the
specified value.
Clearance “C”
: Refer to
JPDIB0164ZZ
Clearance “A”
: Refer to
JPDIB0165ZZ
Clearance “C”
: Refer to
JPDIB0164ZZ
Clearance “A”
: Refer to
JPDIB0165ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст