Nissan Juke F15. Manual — part 1092
RF-34
< REMOVAL AND INSTALLATION >
GLASS LID
REMOVAL AND INSTALLATION
GLASS LID
Exploded View
INFOID:0000000012196980
Removal and Installation
INFOID:0000000012196981
REMOVAL
CAUTION:
• Always work with a helper.
1.
TORX bolt
2.
Glass lid
3.
Sunroof bracket
4.
Drain hose (front)
5.
Drain connector (front)
6.
Sunroof welt
7.
Sunroof motor assembly
8.
Drain hose (rear)
9.
Drain connector (rear)
10. Sunroof unit assembly
11. Seal guide rubber
12. Seal sunroof
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSKIA2884ZZ
GLASS LID
RF-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
• Fully close the glass lid, before removal, then never operate sunroof motor after removal.
1. Remove glass lid mounting TORX bolts (A).
2. Remove glass lid from vehicle.
INSTALLAITON
Note the following items, and then install in the reverse order of removal.
CAUTION:
After installing the glass lid, perform the leak test and check the there is no malfunction.
NOTE:
After installation carry out fitting adjustment. Refer to
Adjustment
INFOID:0000000012196982
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1. Loosen glass lid mounting TORX bolts.
2. Adjust the clearance of glass lid and roof panel according to the fitting standard dimension.
3. To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.
4. Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
JMKIA0029ZZ
JMKIA5137ZZ
1.
Roof panel
2.
Glass lid
Portion
a (Clearance)
b (Surface height difference)
A
− A
0.6
− 2.2 mm (0.024 − 0.087 in)
(
−0.7) − (+2.3) mm [(−0.028) − (+0.091) in]
B
− B
0.6
− 2.2 mm (0.024 − 0.087 in)
(
−0.7) − (+2.3) mm [(−0.028) − (+0.091) in]
C
− C
0.6
− 2.2 mm (0.024 − 0.087 in)
(
−0.7) − (+2.3) mm [(−0.028) − (+0.091) in]
RF-36
< REMOVAL AND INSTALLATION >
GLASS LID
After adjustment the sunroof unit assembly, perform additional service. Refer to
VICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
SUNROOF MOTOR ASSEMBLY
RF-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000012196983
Removal and Installation
INFOID:0000000012196984
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1. Fully close glass lid.
1.
TORX bolt
2.
Glass lid
3.
Sunroof bracket
4.
Drain hose (front)
5.
Drain connector (front)
6.
Sunroof welt
7.
Sunroof motor assembly
8.
Drain hose (rear)
9.
Drain connector (rear)
10. Sunroof unit assembly
11. Seal guide rubber
12. Seal sunroof
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSKIA2884ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст