Nissan Juke F15. Manual — part 38
AV-138
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and front camera connector.
3. Check continuity between around view monitor control unit harness connector and front camera harness
connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit connector and front camera connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector terminals.
Is inspection result normal?
Terminal
Condition
Standard
Reference voltage
(Approx.)
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
6
M98
5
“CAMERA” switch
(around view moni-
tor switch) is ON or
shift position is “R”.
3.5 V or more
6.0 V
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M98
7
E72
4
Existed
8
3
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M98
7
Not existed
8
Terminal
Condition
Standard
Reference value
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
8
M98
7
Shift position is in
“R”.
Waveform accord-
ing to camera image
is input.
JSNIA0834GB
AV
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
AV-139
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
YES
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> Replace front camera. Refer to
AV-191, "Removal and Installation"
.
AV-140
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000012202545
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Shift the selector lever to “R” position.
3. Perform “All DTC Reading” with CONSULT.
4. Check if the “U111D” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111D” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202546
1.
CHECK CONTINUITY SIDE CAMERA LH POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (driver side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (driver
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE SIDE CAMERA LH POWER SUPPLY
1. Connect around view monitor control unit connector and door mirror (driver side) connector.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit harness connector and ground.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U111D
SIDE CAMERA LH IM-
AGE SIGNAL
Camera image signal circuit is open or shorted.
• Camera image signal circuit be-
tween side camera LH and around
view monitor control unit
• Around view monitor control unit
• Side camera LH
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M98
13
D30
6
Existed
14
14
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M98
14
Not existed
AV
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
AV-141
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (driver side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (driver
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit connector and door mirror (driver side) connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector terminals.
Is inspection result normal?
Terminal
Condition
Standard
Reference voltage
(Approx.)
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
14
M98
13
“CAMERA” switch
(around view moni-
tor switch) is ON or
shift position is “R”.
3.5 V or more
6.0 V
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M98
15
D30
7
Existed
16
15
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M98
15
Not existed
16
Terminal
Condition
Standard
Reference value
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
16
M98
15
Shift position is in
“R”.
Waveform accord-
ing to camera image
is input.
JSNIA0834GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст