Nissan Juke F15. Manual — part 1357
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Stores histories when warning/indicator lamp is turned on.
• “Warning History” indicates the “TIME” when the warning/indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO Warning History: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• Warning History is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
NOTE:
In items displayed on the CONSULT screen, only those listed in the above table are used.
Display item
Description
ABS W/L
Lighting history of ABS warning lamp.
VDC/TCS IND
Lighting history of VDC OFF indicator lamp.
SLIP IND
Lighting history of VDC warning lamp.
BRAKE W/L
Lighting history of brake warning lamp.
DOOR W/L
Lighting history of door open warning.
OIL W/L
Lighting history of oil pressure warning lamp.
C-ENG W/L
Lighting history of malfunction indicator lamp.
CRUISE IND
Lighting history of CRUISE indicator lamp.
CVT IND
Lighting history of CVT indicator lamp.
4WD W/L
Lighting history of AWD warning lamp.
FUEL W/L
Lighting history of low fuel level warning lamp.
AIR PRES W/L
Lighting history of low tire pressure warning lamp.
KEY G/Y W/L
Lighting history of KEY warning lamp (G/Y).
KEY KNOB W/L
Lighting history of Shift P warning lamp.
EPS W/L
Lighting history of EPS warning lamp.
WCS-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000013034218
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
WCS
DIAGNOSIS SYSTEM (BCM)
WCS-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000012201475
CONSULT APPLICATION ITEMS
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF
→ ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
WCS-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Display item
[Unit]
Description
PUSH SW
[On/Off]
Status of push-button ignition switch judged by BCM.
UNLK SEN-DR
[On/Off]
Status of unlock sensor judged by BCM.
VEH SPEED 1
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
DOOR SW-DR
[On/Off]
Status of driver side door switch judged by BCM.
CDL LOCK SW
[On/Off]
Status of door lock unlock switch judged by BCM.
Display item
[Unit]
Description
SEAT BELT WARN TEST
The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст