Nissan Juke F15. Manual — part 670
EM-234
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
CATALYST
• Tighten the mounting bolts and nuts in the numerical order
shown in the figure.
- Tighten No. 1 to the specified torque.
- Temporarily tighten No. 2 - 6.
- Tighten No. 2 - 6.
4. Install removed parts in the reverse order of removal.
AWD
A
: To cylinder block
JSBIA5780ZZ
CATALYST
EM-235
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AWD : Exploded View
INFOID:0000000012197419
AWD : Removal and Installation
INFOID:0000000012197420
REMOVAL
1. Remove the EGR guide tube cover and EGR guide tube (catalyst converter). Refer to
.
2. Remove the exhaust manifold cover. Refer to
EM-203, "Removal and Installation"
.
3. Remove the rocker cover protector. Refer to
.
4. Remove heated oxygen sensor 2.
• Remove A/F sensor 1 using a socket designed for heated oxygen sensor removal and installation [SST:
KV10113700 or KV10117100 (J-3647-A)].
CAUTION:
1.
Clamp
2.
Gasket
3.
Catalyst converter
4.
Catalyst converter bracket
5.
Gasket
6.
Heated oxygen sensor 2
7.
Catalyst converter adapter
8.
Catalyst converter adapter bracket
A.
To EGR cooler
B.
To exhaust front tube
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSBIA5767GB
EM-236
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
CATALYST
• If the A/F sensor is dropped from a height of 0.5 m or more onto a concrete or other hard sur-
face, scrap the dropped A/F sensor, and use a new one.
• Before installing a new A/F sensor, clean the A/F sensor installation parts.
5. Remove the mounting nuts and bolts.
6. Remove the catalyst converter adapter bracket, and remove the catalyst converter adapter and gasket.
7. Remove the catalyst converter bracket.
8. Remove the clamp.
9. Remove the catalyst converter and gasket.
CAUTION:
Never subject the catalyst converter to impact.
INSTALLATION
1. Install the gasket between the exhaust manifold and turbocharger assembly and the catalyst converter.
CAUTION:
Check for foreign material on the tightening surface.
2. Follow the procedure below and install the catalyst converter.
• Temporarily fasten the clamp onto the exhaust manifold and
turbocharger assembly, and use the bolts to tempoparily fas-
ten the catalyst converter bracket onto the cylinder head and
catalyst converter (3).
• The mark (1) on the exhaust manifold and turbocharger
assembly should be between the marks (2) on the clamp.
• Tighten the clamp and mounting bolts in the numerical order
shown in the figure.
- Temporarily tighten No. 1 - 3 until each is seated.
- Tighten No. 1 - 3.
3. Follow the procedure below and install the catalyst converter adapter.
E1BIA1281ZZ
E1BIA1282ZZ
CATALYST
EM-237
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Tighten the mounting bolts and nuts in the numerical order
shown in the figure.
- Tighten No. 1 to the specified torque.
- Temporarily tighten No. 2 - 6.
- Tighten No. 2 - 6.
4. Install removed parts in the reverse order of removal.
A
: To cylinder block
JSBIA5781ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст