Nissan Juke F15. Manual — part 1226
TM-94
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
9. Remove transaxle case bolts.
10. Remove bore plug from transaxle case using suitable tool.
CAUTION:
• Do not damage transaxle case.
• Access bore plug from cutout (A) of transaxle case when
removing.
11. Remove transaxle case following the procedures below.
a. Expand snap ring at mainshaft rear bearing accessing from the
bore plug hole. Then pull up transaxle case from clutch housing
until snap ring comes off.
b. With shifter lever A (1) held in the position shown, remove tran-
saxle case from clutch housing.
CAUTION:
Do not drop adjusting shims.
NOTE:
Make sure to hold shifter lever A in the position shown. Other-
wise transaxle case cannot be removed from clutch housing.
PCIB1838E
PCIB1839E
PCIB1840E
PCIB1808E
TRANSAXLE ASSEMBLY
TM-95
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
12. Remove oil gutter A (1) and oil gutter B (2) from transaxle case.
13. Remove snap ring from transaxle case.
14. Remove retaining pin using suitable tool and then remove shifter
lever A and shifter lever B from transaxle case.
15. Remove differential side bearing outer race (transaxle case
side) from transaxle case using Tool. Then remove differential
side bearing adjusting shim from transaxle case.
CAUTION:
Do not damage transaxle case or differential side bearing
outer race.
16. Remove differential side oil seal from transaxle case using suit-
able tool.
CAUTION:
Do not damage transaxle case.
A
: Tab of oil gutter
PCIB1841E
PCIB1842E
PCIB1844E
Tool number
: KV381054S0 (J-34286)
PCIB0936E
SCIA0397E
TM-96
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
17. Remove shifter lever oil seal (1) and striking rod oil seal (2) from
transaxle case.
CAUTION:
Do not damage transaxle case.
18. Remove striking rod shim (1), striking rod adjusting shim (2),
mainshaft rear bearing adjusting shim (3), input shaft rear bear-
ing adjusting shim (4), and reverse idler gear adjusting shim (5).
19. Remove retaining pin of reverse shift fork (1) using suitable tool.
20. Rotate striking lever of striking rod assembly as shown. Then
rotate reverse fork rod to a position where bracket of reverse
fork rod does not interfere with striking lever of striking rod
assembly.
21. Pull out reverse shift fork and reverse fork rod.
22. Remove retaining pin of 5th-6th shift fork (1) using suitable tool.
PCIB1846E
PCIB1858E
2
: Reverse fork rod
PCIB1850E
PCIB1851E
2
: 5th-6th fork rod
PCIB1852E
TRANSAXLE ASSEMBLY
TM-97
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
23. Remove retaining pin of 3rd-4th shift fork (1) using suitable tool.
24. Pull out 3rd-4th fork rod (2).
25. Pull out 5th-6th shift fork (1) and 5th-6th fork rod (2).
26. Pull out 3rd-4th shift fork (1).
27. Remove retaining pin of 1st-2nd shift fork (1) using suitable tool.
28. Pull out 1st-2nd shift fork and 1st-2nd fork rod (2).
29. Remove striking rod assembly (1).
PCIB1853E
PCIB1854E
PCIB1855E
PCIB1856E
PCIB1857E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст