Nissan Juke F15. Manual — part 1374
ROAD WHEEL TIRE ASSEMBLY
WT-39
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000012201871
Removal and Installation
INFOID:0000000012201872
REMOVAL
1. Remove wheel nuts.
2. Remove tire assembly.
INSTALLATION
Note the following, install in the reverse order of removal.
• When replacing or rotating wheels, perform the ID registration. Refer to
.
Inspection
INFOID:0000000012201873
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a. Remove tire from aluminum wheel and mount on a tire balance machine.
b. Set dial indicator as shown in the figure.
c. Check runout, if the axial runout (A) or radial runout (B) exceeds
the limit, replace aluminum wheel.
1.
Tire assembly
: N·m (kg-m, ft-lb)
JSGIA0639GB
Limit
Axial runout (A)
: Refer to
.
Radial runout (B)
: Refer to
.
SEIA0737E
WT-40
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR
Exploded View
INFOID:0000000012201874
CLAMP-IN TYPE
SNAP-IN TYPE
1.
Tire pressure sensor
2.
Grommet seal
3.
Valve nut
4.
Valve core
5.
Valve cap
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Parts that are replaced as a set when the tire is replaced.
JSEIA0572GB
JSEIA1400ZZ
1. Tire pressure sensor
2. Stopper
3. Valve
4. Valve core
5. Valve cap
: Parts that are replaced as a set when the tire is replaced.
: Always replace after every disassembly.
TIRE PRESSURE SENSOR
WT-41
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Removal and Installation
INFOID:0000000012201875
REMOVAL
Clamp-in type
1. Remove tire assembly. Refer to
WT-39, "Removal and Installation"
2. Remove valve cap, valve core and then deflate tire.
NOTE:
If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose
of wheel balance adjustment after installation.
3. Remove valve nut retaining tire pressure sensor and allow tire pressure sensor to fall into tire.
4. Use the tire changer and disengage the tire beads.
CAUTION:
• Verify that the tire pressure sensor (1) is at the bottom of
the tire while performing the above.
• Be sure not to damage the road wheel or tire pressure
sensor.
5. Apply bead cream or an equivalent to the tire beads.
6. Set tire onto the tire changer turntable so that the tire pressure
sensor inside the tire is located close to the road wheel valve
hole.
7. Turn tire so that valve hole is at bottom and bounce so that tire
pressure sensor (1) is near valve hole. Carefully lift tire onto
turntable and position valve hole (and tire pressure sensor) 270
degree from mounting/dismounting head (2).
CAUTION:
Be sure not to damage the road wheel and tire pressure
sensor.
8. Remove tire pressure sensor from tire.
9. Remove the grommet seal.
Snap-in Type
1. Remove tire assembly. Refer to
WT-39, "Removal and Installation"
2. Remove valve cap, valve core and then deflate tire.
NOTE:
If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose
of wheel balance adjustment after installation.
3. Use the tire changer and disengage the tire beads.
CAUTION:
Be sure not to damage the road wheel or tire pressure sensor.
4. Apply bead cream or an equivalent to the tire beads.
5. Turn tire so that valve hole is at bottom and bounce so that tire
pressure sensor (1) is near valve hole. Carefully lift tire onto
turntable and position valve hole (and tire pressure sensor) 270
degree from mounting/dismounting head (2).
CAUTION:
Be sure not to damage the road wheel and tire pressure
sensor.
JPEIC0104ZZ
JPEIC0014GB
JPEIC0014GB
WT-42
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
6. Remove tire pressure sensor (1), follow the procedure below.
a. Remove the stopper (2) in the direction (A), using a pliers.
CAUTION:
Be sure not to damage the tire pressure sensor.
b. Remove the tire pressure sensor from valve (3) in the direction
(B).
7. Cut the part (A) of valve, using a pliers cutters (B).
CAUTION:
Be sure not to damage the road wheel.
8. Turn the valve of 180 degrees using a valve inserter.
NOTE:
In order to ensure safely removing the valve, it is mandatory
before pulling out the valve to either.
9. Cut the roll pin (A) of valve, using a pliers (B).
CAUTION:
Be sure not to damage the road wheel.
10. Remove the valve (1), using a valve inserter (A).
CAUTION:
Be sure not to damage the road wheel.
INSTALLATION
Clamp-in type
1. Apply bead cream or an equivalent to the tire beads.
JSEIA1401ZZ
JSEIA1392ZZ
JSEIA1393ZZ
JSEIA1394ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст