Nissan Juke F15. Manual — part 491
HOW TO SET SRT CODE
EC-777
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
6.
PATTERN 2
1. Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then
release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
• Checking the vehicle speed with GST is advised.
• When steady-state driving is performed again even after it is interrupted, each diagnosis can be conducted.
In this case, the time required for diagnosis may be extended.
>> GO TO 7.
7.
PATTERN 3
• Operate vehicle following the driving pattern shown in the figure.
• Release the accelerator pedal during deceleration of vehicle speed
from 90 km/h (56 MPH) to 0 km/h (0 MPH).
>> GO TO 8.
8.
PATTERN 4
• Operate vehicle following the driving pattern shown in the figure.
- Drive the vehicle in a proper gear at 60 km/h (38 MPH) and main-
tain the speed.
- Release the accelerator pedal fully at least 5 seconds.
- Repeat the above two steps at least 5 times.
>> GO TO 9.
9.
PATTERN 5
• The accelerator pedal must be held very steady during steady-state driving.
• If the accelerator pedal is moved, the test must be conducted again.
>> GO TO 10.
10.
CHECK SRT STATUS
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode of “ENGINE” using CONSULT.
WITHOUT CONSULT
Perform “SRT status” mode with
EC-666, "On Board Diagnosis Function"
.
With GST
Select Service $01 with GST.
Is SRT(s) set?
YES
>> GO TO 11.
NO
>> Call TECH LINE or take appropriate action.
11.
CHECK PERMANENT DTC
NOTE:
Permanent DTC cannot be checked with a tool other than CONSULT or GST.
PBIB2244E
JSBIA0160GB
EC-778
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
HOW TO SET SRT CODE
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
With GST
Select Service $0A with GST.
Is permanent DTC(s) detected?
YES
>> Proceed to
.
NO
>> END
HOW TO ERASE PERMANENT DTC
EC-779
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
HOW TO ERASE PERMANENT DTC
Description
INFOID:0000000012198285
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same mal-
function is not detected after performing the driving pattern for MIL shutoff three times in a raw.
When a DTC is not stored in ECM
The erasing method depends on a permanent DTC stored in ECM. Refer to the following table.
NOTE:
If the applicable permanent DTC includes multiple groups, perform the procedure of Group B first. If the per-
manent DTC is not erased, perform the procedure of Group A.
×: Applicable —: Not applicable
*: For group, refer to
PERMANENT DTC ITEM
For permanent DTC items, MIL turns ON. Refer to
.
*1: When the same malfunction is de-
tected in two consecutive trips, MIL
will illuminate.
*2: MIL will turn off after vehicle is driven
3 times (driving pattern B) without
any malfunctions.
JSBIA0063GB
Group
*
Perform “DTC CONFIRMATION PROCE-
DURE” for applicable DTCs.
Driving pattern
Reference
B
D
A
×
—
—
B
—
×
×
EC-780
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
HOW TO ERASE PERMANENT DTC
PERMANENT DTC SERVICE PROCEDURE
Work Procedure (Group A)
INFOID:0000000012198286
JSBIA0401GB
JSBIA0064GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст